Upload succeeded, but verify failed

Hi I am having a few issues uploading the firmware using the APM mission planner for some reason something is not working right. I am have tried various code AC 2.0.35 and APM 2.2.1And now the code that was working fine seems to be corrupted. If anyone has any quick solutions it would be great to hear them.However, what I want to raise here is that when I get an error message "Upload succeeded, but verify failed" I click OK to acknowledge the message but it does not quit and I have to close all of APM mission Planner to get rid of it.Alastair.

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • I just tried to update my APM 1280 board with APM 2.2.1 HIL using the Planner 1.0.36. (I had a successful upload with Planner 1.0.34.)

     

    I too got the 'Upload succeeded but verify failed' message and Planner hung up.

    Does the CLI still work? 

  • Philip

     

    Ive just tried it on my APM 2560 board and it loaded, are you on a 1280 (that was the board I was having issues with). I am wondering if this is a memory overflow (not sure if that is the right terminology but it sounds good) Issue?

     

    I am wondering if it isn't the Planner as I loaded 2.0.35 yesterday and it worked fine on the 1280 board. Today I am changing over the RX on my quad to 2.4Ghz so I decided to update the planner and then re flash the 2.0.35 and go through the whole set-up again. that when I got the error. Perhaps there is something that the up date has changed that is specific to 1280 APM's

     

    Anyone else having issues?

     

    Alastair

  • I'm having the same problem with 2.0.35 and APM 1.0.36
This reply was deleted.

Activity

DIY Robocars via Twitter
RT @donkey_car: Human-scale Donkey Car! Hope this makes it to a @diyrobocars race https://www.youtube.com/watch?v=ZMaf031U8jg
Jun 25
DIY Robocars via Twitter
Jun 25
DIY Robocars via Twitter
Jun 16
DIY Robocars via Twitter
RT @GrantEMoe: I won my first @diyrobocars @donkey_car virtual race! Many thanks to @chr1sa @EllerbachMaxime @tawnkramer and everyone who m…
Jun 13
DIY Robocars via Twitter
RT @gclue_akira: JetRacerで自動走行したコースを、InstantNeRFで再構築。データセットは別々に収集 #jetracer #instantNeRT https://t.co/T8zjg3MFyO
Jun 13
DIY Robocars via Twitter
RT @SmallpixelCar: SPC 3.0 Now the motor also works. This car is doable. I just need to design a deck to mount my compute and sensors. http…
Jun 13
DIY Robocars via Twitter
RT @SmallpixelCar: My new car SPC 3.0. https://t.co/CKtkZOxeNQ
Jun 7
DIY Robocars via Twitter
RT @SmallpixelCar: High speed at @diyrobocars thanks @EdwardM26321707 for sharing the video https://t.co/o4317Y2U1S
Jun 7
DIY Robocars via Twitter
RT @SmallpixelCar: Today at @RAMS_RC_Club for @diyrobocars. Used @emlid RTK GPS and @adafruit @BoschGlobal IMU. Lap time 28s https://t.co/R…
May 28
DIY Robocars via Twitter
May 15
DIY Robocars via Twitter
May 14
DIY Robocars via Twitter
May 13
DIY Robocars via Twitter
RT @f1tenth: Say hi to our newest #F1TENTH creation for @ieee_ras_icra next week in Philly. It’s going to be huge! 😎 🔥 @AutowareFdn @PennEn…
May 13
DIY Robocars via Twitter
May 11
DIY Robocars via Twitter
May 8
DIY Robocars via Twitter
RT @SmallpixelCar: Noticed my car zigzagged in last run. It turned out to be the grass stuck in the wheel and made the odometry less accura…
May 8
More…