Gender
Male
About
Location
Shanghai
Please tell us a bit about your UAV interest
I spend more time in the basement to develop new things as I spent time to enjoy flying... well I still try to balance my live.
Hometown:
Freudenstadt
Activity Feed
"Sorry, I've updated most manuals recently. The new link is: http://www.mauch-electronic.com/products-manual"
"Just send me an email... christian.mauch@hotmail.com Guy Tzoler said:
Hi
No problem, the FC will be powered form an auxiliary battery of 8s... how can I order those modified sensors? Christian Mauch said:
Hi Guy... to modify the PL-xxx sensors…"
Hi
No problem, the FC will be powered form an auxiliary battery of 8s... how can I order those modified sensors? Christian Mauch said:
Hi Guy... to modify the PL-xxx sensors…"
"Hi Guy... to modify the PL-xxx sensors max. voltage to 150V isn't a problem. However, the max voltage of my biggest BEC's is 100V (Power-Cubes). So you would need an separate LiPo for the FC and attached equipment. Guy Tzoler said:
Hi Christian, …"
Hi Christian, …"
"Hi Michael... the setup is explained on my website: http://www.mauch-electronic.com/manual"
"The information in the Product Guide is updated and includes now Pixhawk 2, to make it easier to select the correct parts for your system.
I offer now 10% discount for anyone who want to be ready for the Pixhawk 2 release. Just enter the Coupon…"
I offer now 10% discount for anyone who want to be ready for the Pixhawk 2 release. Just enter the Coupon…"
"For the power modules are now adapter cables available for the HKPilot 32, with Molex / PicoBlade - 6p connectors.http://www.mauch-electronic.com/apps...s/show/7119616"
"Hi Luc... first of all, the Sensor module does not influence the compass and the source of the interference should be located somewhere else.
Did you calibrate the compass after you installed it in the UAV ?
Are there any high current cables near…"
Did you calibrate the compass after you installed it in the UAV ?
Are there any high current cables near…"
"The new Pixhawk 2 do no more support any backup BEC on the servo rail and can be only powered over the Battery 1 and Battery 2 connector. Therefore, I've added two new BEC's, one for 2-6S LiPo and one for 4-14S LiPo, with Molex Clik-mate 2.0mm…"
"Hi Guy... The hardware is ready for the I2C and the software part is done for my prototype readout display.
I will send you an email, how we can implement the analog value out via I2C."
I will send you an email, how we can implement the analog value out via I2C."
"To reduce shipping time for the Europe customers, the parts are now also available at AltiGator."
"Hi Guy... at the moment the I2C port does not support readout of the total current.
I do not plan to develop 400A sensors. But if you need one, then just connect two 200A sensors in parallel. I believe the very low IR of the ACS758 will be enough…"
I do not plan to develop 400A sensors. But if you need one, then just connect two 200A sensors in parallel. I believe the very low IR of the ACS758 will be enough…"
"For the power modules are now adapter cables available for the Pixhawk 2, with Molex Clik-Mate 6p 2.0mm.http://www.mauch-electronic.com/apps/webstore/"
"Hi Sandy... we should not summarize the max. current of the ESC's. Instead, we should look at the estimated hovering current with full payload (AUW).
Then we use the following rule:
Current 10-30A = 50A Sensor
Current 30-60A = 100A Sensor
Current…"
Then we use the following rule:
Current 10-30A = 50A Sensor
Current 30-60A = 100A Sensor
Current…"
"A half year has passed since I introduced the Sensor board and I sold quite a number... thanks to everybody ! Anyhow, the cable standard or all sensors (50A, 100A and 200A) was 2x 10cm 12AWG wires and only a few guys requested a change to 10AWG. But…"
"The 12.0V version of the 4-14S HYB-BEC for FPV is now available !"
"Hi Guy... yes, a 400Amp setup with single battery would be possible with 2x HS-200-xx Sensors together with an Sensor Hub X2. But you should consider to use two batteries in parallel due to the high current... may I ask which battery you…"
