DSC_0343.jpg

The wait is over! We are proud to introduce the next generation 3DR autopilot, Pixhawk Mini. Pixhawk Mini is an upgraded Pixhawk designed in collaboration with HobbyKing and optimized to run the Dronecode PX4 firmware stack and QGroundControl multi-platform ground station (Windows, Mac, Linux, Android, iOS).

For just $199, Pixhawk Mini includes autopilot, GPS, and all the cables and connectors needed to get started building DIY quads, planes, rovers, and boats.

What's improved over Pixhawk 1?

  • One third the size--dimensions reduced from 50 mm x 81.5 mm x15.5 mm to 38 mm x 43 mm x 12 mm. Smaller airframes can now operate autonomously without making sacrifices for the Pixhawk footprint.

  • Rev 3 STM32 processor allow for full utilization of 2MB flash memory. Pixhawk Mini operates at only 50% compute capacity, 40 percentage points lower than the original Pixhawk. There is significantly more overhead available to run custom code.

  • Improved sensors, including both primary and secondary IMU (MPU9250 and ICM20608, respectively), lead to much better vibration handling and increased reliability.

  • GPS module included--Neo M8N with quad-constellation support and upgraded HMC5983 compass.

  • Micro JST connectors replace DF-13. We can all breath a sigh of relief.

  • Integrated piezo speaker and safety switch

What's improved over Pixfalcon?

  • Again, improved sensors, including both primary and secondary IMU (MPU9250 and ICM20608 respectively) for much better vibration handling and increased reliability.

  • Dedicated CAN port for UAVCAN applications.

  • Includes 8-channel servo output board for planes and other vehicles requiring powered PWM output.

  • Includes I2C breakout board for a total of 5 I2C connections.

Pixhawk Mini features an advanced processor and sensor technology from ST Microelectronics® and a NuttX real-time operating system, delivering incredible performance, flexibility, and reliability for controlling any autonomous vehicle.

SPECIFICATIONS

  • Main Processor: STM32F427 Rev 3

  • IO Processor: STM32F103

  • Accel/Gyro/Mag: MPU9250

  • Accel/Gyro: ICM20608

  • Barometer: MS5611

  • Dimensions: 38x43x12mm

  • Weight: 15.8g

GPS Module: ublox Neo-M8N GPS/GLONASS receiver; integrated magnetometer HMC5983

  • Dimensions: 37x37x12mm

  • Weight: 22.4g

Interface

  • 1 x UART Serial Port (for GPS)

  • Spektrum DSM/DSM2/DSM-X® Satellite Compatible RC input

  • Futaba S BUS® Compatible RC input

  • PPM Sum Signal RC Input

  • I2C (for digital sensors)

  • CAN (for digital motor control with compatible controllers)

  • ADC (for analog sensors)

  • Micro USB Port

What’s Included?

  • Pixhawk Mini Flight Controller

  • GPS with uBlox M8N module with  

    • Concurrent reception of up to 3 GNSS (GPS, Galileo, GLONASS, BeiDou)

    • Industry leading –167 dBm navigation sensitivity

    • Security and integrity protection

    • Supports all satellite augmentation systems

    • Advanced jamming and spoofing detection

    • Product variants to meet performance and cost requirements

    • Backward compatible with NEO‑7 and NEO‑6 families

  • Integrated Power Module (up to 6s batteries) and power distribution board for quadcopters

  • 8-channel servo output board for planes and other vehicles requiring powered PWM output.

  • Cables

    • 4 pin I2C cable and breakout board

    • 6 pin GPS+Compass cable

    • 6 to 6/4 ‘Y’ adapter for additional I2C devices

    • 4 JST to 6 DF13 cable for legacy telemetry radios

    • External safety switch cable

    • RCIN cable for PPM/SBUS input

    • 8 channel RC output cable

    • 6 pin power cable for included Power Distribution Board

OPTIONAL ACCESSORIES

All available here

 

Views: 22556

Comment by kane vincia on October 27, 2016 at 10:45pm

Really impressive work, smaller and ever more powerful!

Comment by Jerry Giant on October 27, 2016 at 11:14pm

important things deserve repeat three times, really?

Comment by Roman on October 28, 2016 at 12:04am

@Jerry Giant, yep sure)

Comment by Andreas Gazis on October 28, 2016 at 12:39am

Looks neat. How does it perform when running Ardupilot?

Comment by Jiro Hattori on October 28, 2016 at 1:10am

I would like to know, what's improved or changed over PixFalcon Micro PX4 ?

Comment by Nick Sargeant on October 28, 2016 at 1:21am

3DR is dead.

Comment by khadu09 on October 28, 2016 at 1:38am

Pixhawk mini:

  • Main Processor: STM32F427 Rev 3

  • IO Processor: STM32F103

  • Accel/Gyro/Mag: MPU9250

  • Accel/Gyro: ICM20608

  • Barometer: MS5611

XRacer V1:

MCU - STM32F427VIT6 rev.3

FRAM - FM25V02-G

Ultra low noise LDOs for sensors and FMU

MPU9250, HMC5983, ICM20608, baro MS5611

Pixhawk mini running firmware PX4 V4???

Comment by lot on October 28, 2016 at 2:14am

The manufacturing is made by 3DR or by Hobbyking?

Comment by Johnatan on October 28, 2016 at 2:45am

It seems the only difference vs Pixracer is that Pixhawk mini is equipped with"IO Processor: STM32F103".

Comment by Auturgy on October 28, 2016 at 3:54am
3DR is a Hobbyking reseller now!
The irony is awesome.

Comment

You need to be a member of DIY Drones to add comments!

Join DIY Drones

© 2017   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service