Replies

  • Hi. Looks like your receiver antenna is nearly touching the 5.8 video antenna. That wire antenna from the receiver is at some point in its length resonate with 5.8 ghz and RF energy will be introduced into the receiver electronics, possibly swamping incoming 2.4 ghz signals. Simply stated you should always place antennas for different electronic devices as far apart as is possible. 5.8 ghz wave length is about 2 inches long. Radio frequency energy is subject to the inverse square law just like light. So if your receiver antenna is 2 inches from the 5.8 antenna it is receiving twice the amount of interfering energy that it would receive at 2.8 inches, to half that again move them apart by 4 inches and cut it in half again by separating them to 5.6 inches and so on. separate them by as many wave lengths as possible. Small cheap electronics rarely have good filtration against interference. Once you've separated the antennas by as far as possible, if interference is still a problem, install a copper wire mesh screen, perhaps 3 inches in diameter above the 5.8 ghz antenna in your installation in the photo. It could be fitted to the 5.8 coax by poking a hole in the screen and gluing it in place an inch or more above the antenna. This would create RF shielding, keeping the the 5.8 GHZ RF from radiating toward the other electronics. Grounding the mesh would further enhance the shielding.

    Hope this helps

    Geoffrey

This reply was deleted.

Activity

DIY Robocars via Twitter
RT @SmallpixelCar: My car was able to go all the way autonomously until the crosswalk. It was only 100 yards from the target. What should b…
8 hours ago
Liam left a comment on Agricultural UAVs
"Hi
I'm Liam from T-MOTOR. I would like to reach out to see if there is any possibility for us to work together.
We are a propulsion system manufacturer who offers motors, propellers and ESCs for all kinds of drone applications which vary from secur…"
Wednesday
DIY Robocars via Twitter
RT @SmallpixelCar: Smart move. The car used the shadow to guide it through the bridge. This was never in the training samples. But it learn…
Wednesday
DIY Robocars via Twitter
RT @SmallpixelCar: Getting closer to the target. Single camera. Untrained road. https://t.co/Wsr7RwDamj
Tuesday
Richard Cox left a comment on Australia
"Anyone in the DIYDRONES Australian subgroup based in Alice Springs, NT?
I am experimenting with Ardupilot (standard Arduplane), Pixhawk 4 FC in a 4-ch
RC "AXN Floater Jet" foamy plane..."
Tuesday
Omar Sykes left a comment on Australia
"Hi everyone, I am looking for someone who is good at drone building, repair and software in Adelaide. Please give me a call on 0477 319 219."
Tuesday
DIY Robocars via Twitter
RT @RoboticMasters: #donkeycar https://t.co/czuLoVRcA4
Monday
DIY Robocars via Twitter
https://t.co/DKQbNTbz0g
Monday
DIY Robocars via Twitter
RT @RoboticMasters: Donkey car, car car car car car car; Donkey car, car car car car car car; Donkey Car. Anyone like our tiny tiny donkey…
Monday
DIY Robocars via Twitter
RT @SmallpixelCar: After improving DBSCAN speed, I can get 11 frame per second on @NVIDIAEmbedded Jerson Xavier MAXN mode and the autonomou…
Jun 26
DIY Robocars via Twitter
RT @Heavy02011: Join us at next Virtual Race League: ⁦@diyrobocars⁩ Race #4 - Parking Lot Nerds, August 1st https://t.co/5KUpu7VGaH
Jun 25
DIY Robocars via Twitter
RT @SmallpixelCar: #CUDA implementation should be easy, because most of the time is on distance calculations berween two points and if the…
Jun 25
DIY Robocars via Twitter
RT @SmallpixelCar: This is the view from the car. Even my lanenet inference is fast on @NVIDIAEmbedded Jerson Xavier, DBSCAN clustering tak…
Jun 25
DIY Robocars via Twitter
RT @SmallpixelCar: Ran my car in the park, with single camera and @sparkfun IMU. #TensorRT on @NVIDIAEmbedded Jetson Xavier. Lanenet one fr…
Jun 24
DIY Robocars via Twitter
RT @SmallpixelCar: Making progress on drive the car autonomously in my neighborhood. This run used single camera only. No other sensors. ht…
Jun 24
DIY Robocars via Twitter
RT @chr1sa: The @DIYRobocars/@donkey_car AI racers are getting *fast* in the simulator, in part because it's so well optimized for reinforc…
Jun 21
More…