ArduPilot Throttle Channel

Hello All,Getting a setup going. Everything appears to be working well, except the throttle.Obviously, going straight into the Rx works just fine.The ESC normally plays a startup tone, and then 3 beeps to let me know it's ready. It does this when going straight into the Rx.If I jump the Rx into the "in" side of ardupilot.And hook the ESC into channel 3 on "out" side.I get the startup tone, but not the following three beeps.Has anyone else experienced something like this?I've quadruple checked the servo connections, and they're correct.Any suggestions?Thank you!John C.

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • hello people, i think i have a problem with the mux (ch3 and ch4), i have been searching and reading the webpage from top to bottom and i can´t make it work...

    :-(
    look at this:

    GPS... OK
    IMU... OK
    INPUTS:
    AIRSPEED...OK
    CH1.............OK
    CH2.............OK
    CH3.............OK
    CH4.............OK

    OUTPUTS
    CH1.........OK
    CH2.........OK
    CH3..........BAD TRYED CHANGING TO MUX4 not working
    CH4..........BAD

    TELEMETRY.........OK

    CGS.....................OK


    any ideas?

    seems like i am going to try and fly without throttle and without rudder also (seems like ardupilot does not support using ailerons and vtail at the same time.....
    can you please give me some ideas on what else to try..... waited long time for my ardupilot to arrive... :-(
  • I don't think this is an isolated issue as I had exactly the same problem with mux 3 and only found out recently when I started using throttle. Thanks to this post I also fixed it using mux 4.
  • John, It's possibe the mux chip could have been damaged be ESD. All is not lost. You could use chn. 4 by moving the wire from mux 3 to mux 4 and solder on the extra connectors. The Aurdupiolot doesn't read inputs 3 & 4, it's not wired. These channel's outputs are just switched from computer to receiver when going to man. mode. If it works, that would confirm the problem plus get you going right away.
  • Developer
    Check the continuity between the pins and these two pins on the mux.

  • 3D Robotics
    I assume you soldered the jumper wire so channel 3 is enabled?
  • Developer
    Sounds like you need to adjust the minimum throttle servo value in the header file to a lower value. I am not familiar with the Plush, but most speed controllers will not arm unless they see a low enough throttle signal (i.e. stick all the way down). If you want to test this idea hook the esc up to the rx and start it up at say 1/4 stick. If you get the same behaviour then this is what is happening and what you need to adjust. Just be careful in case the Plush does not have this feature in which case your prop will spin!
  • Admin
    John,

    I believe that the ESC is looking for a throttle control signal which it gets from the Rx at power up.

    What position do you have your Ardupilot CNTL signal at when powering up? It should be in manual. Looks like the throttle control signal is not being passed through the Ardupilot mux from the Rx when in manual.

    Just a thought.

    Regards,
    TCIII
This reply was deleted.

Activity

DIY Robocars via Twitter
RT @_JonMyer: 🚨Attention DeepRacer's including #UndergroundDeepRacer🚨 Check our our LIVE stream that including @IAM_dbro Take a few moments…
Wednesday
DIY Drones via Twitter
RT @MarvelmindMaxim: Extreme precision for 60 swarming robots. #marvelmind #autonomousrobotics #robotics #swarmrobotics #rtls #ips #indoor…
Aug 3
DIY Drones via Twitter
RT @MarvelmindMaxim: Precise (±2cm) tracking for racing boats and autonomous boats. Works outdoor and indoor. #autonomous #AutonomousVehic…
Aug 3
DIY Drones via Twitter
RT @MarvelmindMaxim: Helping PixHawk folks to fly autonomous quadcopters using PX4 and ArduPilot. https://marvelmind.com/drones/ Equally suitab…
Aug 3
DIY Robocars via Twitter
RT @chr1sa: The @DIYRobocars @donkey_car virtual AI car race is starting in 15 minutes! Watch it live on Twitch https://www.twitch.tv/mossmann3333 htt…
Aug 1
DIY Robocars via Twitter
RT @chr1sa: Don't miss our monthly @DIYRobocars @donkey_car virtual AI car race tomorrow at 10:00am PT live on Twitch. Head-to-head racing…
Jul 31
DIY Robocars via Twitter
RT @sparkfun: Our completed tutorial on building an @NVIDIA Jetson Nano-powered @Sphero RVR gets your bot up and running via teleoperation…
Jul 30
DIY Robocars via Twitter
RT @SmallpixelCar: Freeway test https://t.co/4V5tV9lhIP
Jul 29
DIY Robocars via Twitter
Very small autonomous cars racing, thanks to an overhead camera: https://control.ee.ethz.ch/research/team-projects/autonomous-rc-car-racing.html
Jul 29
DIY Robocars via Twitter
Jul 29
DIY Robocars via Twitter
Jul 29
DIY Robocars via Twitter
RT @chr1sa: Don't miss our virtual AI car race this Saturday! Real developers + virtual cars =🏎️🏎️🏎️ Head-to-head battles with thrills, sp…
Jul 28
DIY Robocars via Twitter
Jul 27
DIY Robocars via Twitter
RT @usashirou1: Jetson nano by Isaac Kaya #jetson https://t.co/Mu1N0CyQkN
Jul 23
DIY Robocars via Twitter
RT @GPUsolution: JetRacer mady by Iflytek company #JetsonNANO #Nvidia https://t.co/MimTymIwge
Jul 23
DIY Robocars via Twitter
RT @openmvcam: I love this: Mega or Mini? Image Classification on the 1MB OpenMV Cam H7 by Ish Ot Jr. in OpenMV, Edge Impulse, Internet of…
Jul 23
More…