"Bad Gyro Health" apm 2.6 mega

i'm not sure exactly where to post this but I hope someone can help me.  I purchased the APM 2.6 Mega with Ublox GPS (with compass), minum osd, 3dr power module, and telemetry from Readytoflyquads.com. 

I have setup the board and run Mission Planner wizard with no problems.  I calibrated and leveled my accelerometers and Mission Planner showed the artificial horizon as level as long as I don't move the board.  When I do move the board the horizon on the computer responds correctly to my movements but when I place it back on the table the horizon continues to move as far as 60 degrees back and forth until I unplug the board.  I also occasionally get a "bad gyro health" error.  

I have uploaded a video to Youtube which can be found here: https://www.youtube.com/watch?v=QxJBEwjVpVo

If someone could please look at it and see if I am doing something wrong I would really appreciate it.

Thanks in advance.

Jamie

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • I read thinking of doing that but I can't seem to figure out how to load the older firmware. Is it available for download somewhere?
    • In Mission Planner, go to the Initial Setup tab. Click Install Firmware. Bottom right is a "previous versions" option.

      • I checked my mission planner and I don't have the previous version button. I read online that ctrl O will pull up previous versions but that does not work also.
        • I've attached an image of what you should see.

          capture.PNG

          https://storage.ning.com/topology/rest/1.0/file/get/3702752198?profile=original
          • I see the exact same screen you have there except for the options in the lower right. I'm running mission planner 1.2.99 build 1.1.5197.12871, what version are you using? Thanks for your time.

            1395877918406.jpg

            • 1.2.97 but I can't imagine an update would remove that feature. I'll keep looking at it. Perhaps there's an option to display that menu somewhere.

              • I installed 1.3.4 today. The option to install older firmware is not there. I'm getting the Bad Gyro Health message; I checked the I2C port voltage, its giving out 4.4V. I have an APM 2.5 from jDrones. I've had it for over a year now, just got it setup now. Had been using the APM 2 before this. I wanted to know what gets affected if you've got a blown regulator. Is there any way the board is still usable?

                • Alright, I went into Config/Tuning and checked Advanced View. That brought those options back. Hope this helps :)

  • Hey, I had the same problem. What fixed it for me was rolling back to an earlier version of ArduPlane. I think 2.76.

    • Thank you!  That fixed my Bad Gyro problem as well

This reply was deleted.

Activity

DIY Robocars via Twitter
RT @a1k0n: @SmallpixelCar @diyrobocars It's just something that's easy to track with chroma keying. I ended up using different colors on th…
Monday
DIY Robocars via Twitter
Monday
DIY Robocars via Twitter
RT @TinkerGen_: "The Tinkergen MARK ($199) is my new favorite starter robocar. It’s got everything — computer vision, deep learning, sensor…
Nov 23
DIY Robocars via Twitter
Nov 23
DIY Robocars via Twitter
RT @roboton_io: Join our FREE Sumo Competition 🤖🏆 👉 https://roboton.io/ranking/vsc2020 #sumo #robot #edtech #competition #games4ed https://t.co/WOx…
Nov 16
DIY Drones via Twitter
First impressions of Tinkergen MARK robocar https://ift.tt/36IeZHc
Nov 16
DIY Robocars via Twitter
Our review of the @TinkerGen_ MARK robocar, which is the best on the market right now https://diyrobocars.com/2020/11/15/first-impressions-of-tinkergen-mark-robocar/ https://t.co/ENIlU5SfZ2
Nov 15
DIY Robocars via Twitter
RT @Ingmar_Stapel: I have now explained the OpenBot project in great detail on my blog with 12 articles step by step. I hope you enjoy read…
Nov 15
DIY Robocars via Twitter
RT @DAVGtech: This is a must attend. Click the link, follow link to read the story, sign up. #chaos2020 #digitalconnection #digitalworld ht…
Nov 15
DIY Robocars via Twitter
RT @a1k0n: Got a new chassis for outdoor races (hobbyking Quantum Vandal) but I totally didn't expect that it might cause problems for my g…
Nov 11
DIY Drones via Twitter
First impressions of the Intel OpenBot https://ift.tt/36qkVV4
Nov 10
DIY Robocars via Twitter
Nov 9
DIY Robocars via Twitter
Excellent use of cardboard instead of 3D printing! https://twitter.com/Ingmar_Stapel/status/1324960595318333441
Nov 7
DIY Robocars via Twitter
RT @chr1sa: We've got a record 50 teams competing in this month's @DIYRobocars @donkey_car virtual AI car race. Starting today at 10:00am…
Nov 7
DIY Robocars via Twitter
Nov 6
DIY Robocars via Twitter
RT @a1k0n: Car's view, using a fisheye camera. The ceiling light tracking algorithm gave me some ideas to improve ConeSLAM, and having grou…
Nov 5
More…