Gender
Male
About
Location
Kolkata, West Bengal.
Please tell us a bit about your UAV interest
Anything autonomous. Anything to fly. FPV for life!
Hometown:
Kolkata, India
Activity Feed
"Hey Patrick! We finally made it to DIYDrones! Been my dream ever since I started using ArduPilot. Thanks Patrick :D"
"So this is a good thing, correct? If the Pixhawk ever browns out for whatever reason, the chute will auto-deploy to save the craft?
Thanks."
Thanks."
"Hi I've added the line to .bashrc as specified in the new page at http://dev.ardupilot.com/wiki/sitl-native-on-windows/
Now when I cd in ardupilot/ArduCopter and then try running
make sitl -j4 and I've also tried it without the -j4
I'm getting the…"
Now when I cd in ardupilot/ArduCopter and then try running
make sitl -j4 and I've also tried it without the -j4
I'm getting the…"
"Hi I've added the line to .bashrc as specified in the new page at http://dev.ardupilot.com/wiki/sitl-native-on-windows/
Now when I cd in ardupilot/ArduCopter and then try running
make sitl -j4, I'm getting the same SKETCHBOOK not found error.
I…"
Now when I cd in ardupilot/ArduCopter and then try running
make sitl -j4, I'm getting the same SKETCHBOOK not found error.
I…"
I have to do a final semester project for a quad to auto-land on a target. Is this possible using and APM, a raspberry pi? I've used the APM for quite a while now, and know my way around how to get it set up, tune it and fly using it but am not too…
"And try not to give up on the APM :)
It's really brilliant, you just need to pay attention to details, read the wiki carefully. :D"
It's really brilliant, you just need to pay attention to details, read the wiki carefully. :D"
"http://copter.ardupilot.com/wiki/altholdmode/
^^ Have you read points 1 ans 2 under Common Problems?
And then:
http://copter.ardupilot.com/wiki/ac_throttlemid/
Try adjusting that.
I'd built a smallish quad and althold didn't work properly. Fixed…"
^^ Have you read points 1 ans 2 under Common Problems?
And then:
http://copter.ardupilot.com/wiki/ac_throttlemid/
Try adjusting that.
I'd built a smallish quad and althold didn't work properly. Fixed…"
"I once had a similar problem, wouldn't arm and wouldn't show any error on the HUD. Recalibrated compass very carefully, and it worked after that."
Hi, I've got a jDrones APM 2.5(not 2.5.x). I had the regulator fail, and had gotten it replaced. After that the board works fine. I've used it on the HobbyKing Talon tricopter frame and now I've got it setup on the HobbyKing X650 frame. I setup…
"I'm getting the same error on my APM 2.5 (not 2.5.x). 3.3V regulator is fine. Baro and compass tests run fine in the CLI. I tried what you suggested, squeezing the chip. That didn't help. Any ideas what might be wrong?"
"Have a look at this if you haven't already: http://diydrones.com/forum/topics/ac3-1-rc5-spi-speed-problem
I have an APM2.5, had a bad 3.3V regulator. Used to have 4.16V on the 3.3V rail, but all my sensors used to behave well. Well, most of the…"
I have an APM2.5, had a bad 3.3V regulator. Used to have 4.16V on the 3.3V rail, but all my sensors used to behave well. Well, most of the…"
"Is it safe enough to just disconnect the GPS physically, or is it advisable to change any of the params as well? And what would the behaviour be, in both the above cases, if by chance the flight mode changes to one that uses the GPS? Thanks."
"Chris, could this have anything to do with the PPM Encoder? I was using a Futaba T8fg with the bundled 8ch rx. Kept twitching in flight. Then I came across the info that Futaba 8ch rx had problems with the PPM Encoder. I'm making a wild guess, and…"
"Nice, lucky story!
Could it have triggered the gps glitch failsafe since it was flying between buildings?"
Could it have triggered the gps glitch failsafe since it was flying between buildings?"
"Logs on XD"
