Performance research 250g quad

Hello I am an Aerospace Engineer working in aircraft industry (Cessna, Boeing, etc). My professional work is in structural analysis and I also have a background in low Reynolds number aerodynamics. I'm interested in conducting research and development on < 250g quad. I believe current designs could benefit from aerodynamic improvements for greater flight time/payload/speed/etc. I would specifically like to make improvements to the DJI Mini Mavic or similar airframe. I have extensive experience in traditional RC fixed wing/helicopters but I'm completely new to quads.

Questions:

1) Is it possible to tune the PID of the autopilot of a DJI copter if I were to change some of the airframe characteristics?

2) If I build a custom airframe and transplant the DJI electronics I may end up with the board that contains the accelerometers in a different orientation. Is it possible to remap the accelerometers of the DJI electronics?

3) Am I better off just buying electronic components intended for custom builds rather than trying to retune the DJI guts in a new airframe?

4) What are the best components (autopilot/esc/transmitter/receiver) that would be suitable for 250g airframe custom build?

Thanks,

Paul Klusman

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • what is the point of hacking DJI ? why not select a flight controller  ESC & motors that will give you the best performance ? 

    as per aerodynamics it does not matter that much at 250 scale ether if you flew lots of models you would know that!! lots of hardware out there on the market... 

  • Thanks Michael. I've found a number of groups dedicated to hacking DJI but it is usually to remove flight restrictions. Very little activity in the DJI community modifying hardware/aerodynamics for improved endurance beyond just adding another battery strapped to the body of the copter. I believe most of the copters on the market could benefit from improved efficiency. They all look cool but most of them have the aerodynamics of a toaster.

    Michael McDon said:

    Paul, 

    For investigating these options, I'd stay away from DJI.  Though the SDK does provide access to a good bit of the functionality software, the firmware and hardware are another story.  I'm trying to do a simple remap of the GPS unit on a Mavic 2, and have not been having a lot of success outside of traditional and tiresome reverse engineering work.  I'd go with option 3. That's basically what I've come up with after about 6 months worth of work in my spare time on the Mavic.  For autopilot, just go with a premade FRUv5 unit like the pixhawk4. The rest is all up to how much you want to spend.  There are a lot of good options.  

    Performance research 250g quad
    Hello I am an Aerospace Engineer working in aircraft industry (Cessna, Boeing, etc). My professional work is in structural analysis and I also have a…
  • interesting proposition that has been done already the issue is a more efferent air frame will only matter while the craft is in motion not while in hover! copters hover a lot depending on application increasing  endurance during hover is a goal  to chase!

    selecting the correct parts alone will increase your flight time by a lot !    

  • Paul, 

    For investigating these options, I'd stay away from DJI.  Though the SDK does provide access to a good bit of the functionality software, the firmware and hardware are another story.  I'm trying to do a simple remap of the GPS unit on a Mavic 2, and have not been having a lot of success outside of traditional and tiresome reverse engineering work.  I'd go with option 3. That's basically what I've come up with after about 6 months worth of work in my spare time on the Mavic.  For autopilot, just go with a premade FRUv5 unit like the pixhawk4. The rest is all up to how much you want to spend.  There are a lot of good options.  

This reply was deleted.

Activity

DIY Robocars via Twitter
RT @gclue_akira: 柏の葉で走行させてるjetracerの中身 #instantNeRF #jetracer https://t.co/giVvuE4hP7
Jul 4
DIY Robocars via Twitter
Cool web-based self-driving simulator. Click save when the AI does the right thing https://github.com/pncsoares/self-driving-car
Jul 4
DIY Robocars via Twitter
RT @donkey_car: Human-scale Donkey Car! Hope this makes it to a @diyrobocars race https://www.youtube.com/watch?v=ZMaf031U8jg
Jun 25
DIY Robocars via Twitter
Jun 25
DIY Robocars via Twitter
Jun 16
DIY Robocars via Twitter
RT @GrantEMoe: I won my first @diyrobocars @donkey_car virtual race! Many thanks to @chr1sa @EllerbachMaxime @tawnkramer and everyone who m…
Jun 13
DIY Robocars via Twitter
RT @gclue_akira: JetRacerで自動走行したコースを、InstantNeRFで再構築。データセットは別々に収集 #jetracer #instantNeRT https://t.co/T8zjg3MFyO
Jun 13
DIY Robocars via Twitter
RT @SmallpixelCar: SPC 3.0 Now the motor also works. This car is doable. I just need to design a deck to mount my compute and sensors. http…
Jun 13
DIY Robocars via Twitter
RT @SmallpixelCar: My new car SPC 3.0. https://t.co/CKtkZOxeNQ
Jun 7
DIY Robocars via Twitter
RT @SmallpixelCar: High speed at @diyrobocars thanks @EdwardM26321707 for sharing the video https://t.co/o4317Y2U1S
Jun 7
DIY Robocars via Twitter
RT @SmallpixelCar: Today at @RAMS_RC_Club for @diyrobocars. Used @emlid RTK GPS and @adafruit @BoschGlobal IMU. Lap time 28s https://t.co/R…
May 28
DIY Robocars via Twitter
May 15
DIY Robocars via Twitter
May 14
DIY Robocars via Twitter
May 13
DIY Robocars via Twitter
RT @f1tenth: Say hi to our newest #F1TENTH creation for @ieee_ras_icra next week in Philly. It’s going to be huge! 😎 🔥 @AutowareFdn @PennEn…
May 13
DIY Robocars via Twitter
May 11
More…