MR60

XUAV Talon on its way

Posted by Hugues on March 26, 2014 at 5:12am

Hello,

I decided to take a big jump into arduplane & pixhawk by purchasing a XUAV Talon as my first APM plane. I hear already some voices say I should have started with a Bixler but I should already benefit from my Arducopter knowledge, I hope.

I ordered at fpv model because there are no Talon offering in Europe (one in Switzerland but three times the price). It should arrive in a few days.

I have to decide on motor and prop. I have read some good combinations like a 550kv T-motor with 12x6 prop; or for longer flights a low kV config such as a T-motor 400kv with 15x5 prop (in 6S battery config).

Do you guys have good advices for me? 

I would also be interested by your PID params for your Talon config.

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –
Follow

Replies

  • MR60
    Hugues May 25, 2014 at 12:24pm

    For information, with the following motor configuration:

    4S config and a rctiger MN3510-700Kv with a 13x8 prop, I measured on the bench 1000 gr of thrust at 50% throttle , for a consumption of 8.8 amps (battery at 3.8V per cell)

  • MR60
    Hugues May 25, 2014 at 12:22pm

    Build blog here :

    http://diydrones.com/profiles/blogs/xuav-talon-build-part-3-interna...

  • MR60
    Hugues May 16, 2014 at 1:21pm

    About motor for the Talon, i will first use a 4S config (to start lighter than with 6S) using a rctiger MN3510-700Kv with a 13x8 prop. Once I get to fly it correctly, I will move to a 6S with rctiger AT2826-550KV and 12x6 prop.

  • Ujjwal John April 15, 2014 at 1:10pm

    Ordered the Red Talon from Fpvstyle with free Wing extension!! Talon was available with my LHS at a bit higher cost, but the deal at FpvStyl ($99 + $40 shipping + Wing extension free ) was tempting.

    I have Axi 2826/8 (around 11(around 920kv) lying with me. Would they be good for Talon ?? I have seen  people using lover KV motor and higher Cell count of 6S for long flight but Axi are known for their efficiency.

  • MR60
    Hugues March 26, 2014 at 10:41am

    Thx for your advice's.

    I spotted these wing extensions as well. 

    Christian, are you selling those?

    • Moderator
      Bill Piedra > Hugues July 2, 2014 at 1:40pm

      If you find a US seller for the wing extensions please let me know.  I would also like to order a set.  

    • Christiaan van Vollenstee > Hugues March 26, 2014 at 11:37pm

      Unfortunately only to South Africa, the shipping to the rest of the world is way to expensive. FPV Model might be selling them its best you contact them.

    • Drone-University.com > Christiaan van Vollenstee April 11, 2014 at 5:59am

      Hi,

      I am opening a drone school in France and I want to purchase a Talon for advanced training, while students will most certainly want to purchase it also at the end of their training.

      Is fpvmodel the only way to ship to Europe ? Shipping cost is just horrendous, and I am not even talking about custom taxes. A European hub for selling the talon would be great.

    • Christiaan van Vollenstee > Drone-University.com April 11, 2014 at 6:15am

      If you can do a bulk order like 5 planes I can send it to you via china directly from the manufacture.

    • Drone-University.com > Christiaan van Vollenstee May 15, 2014 at 1:32pm

      Thank you. A firend of mine purchased the Talon and for my needs, it is eventually not the plane I need ( Talon has a relatively high stall speed,  flies at a high speed in general, and is not so good in 2 axes so not adequate for a school ).

This reply was deleted.