About

Gender

Male


Location

Ottawa, Ontario


Please tell us a bit about your UAV interest

Owner of 4, 6 and 8 rotor UAV


Hometown:

Ottawa


Activity Feed

Frederic Charpentier commented on Chris Anderson's blog post New product in the DIY Drones store: 8-ch PPM encoder
"(Yet another) update: after flashing the PPM encoder that DID have the external oscillator (16 Mhz), I was able to have it work with the quad -- first flight was a success. This confirms that the problem I was experiencing with the 2/3 levels was…"
Jun 17, 2010
Frederic Charpentier commented on Chris Anderson's blog post New product in the DIY Drones store: 8-ch PPM encoder
"Update -- I only realized now that I got 2 different boards!... One has the crystal. The other one does not. Foolish me, I assumed that they were identical. So I think that what happened was that I programmed the 8Mhz board with the 16 Mhz hex file.…"
Jun 17, 2010
Frederic Charpentier commented on Chris Anderson's blog post New product in the DIY Drones store: 8-ch PPM encoder
"Chris,
Could you please direct me to that tutorial.. I screwed something up and I can't read the device anymore."
Jun 17, 2010
Frederic Charpentier commented on Chris Anderson's blog post New product in the DIY Drones store: 8-ch PPM encoder
"Maybe I should have specified that I am using a Futaba 6008HS as a receiver..."
Jun 16, 2010
Frederic Charpentier commented on Chris Anderson's blog post New product in the DIY Drones store: 8-ch PPM encoder
"Well.. I ran into another snag. First of all, I had to reassign the channels on the Futaba xmtter -- at elast temporarily -- to get throttle on channel 3. Now the PPM encoder blinks on power on. But... when I look at the channel output on the quad's…"
Jun 16, 2010
Frederic Charpentier commented on Chris Anderson's blog post New product in the DIY Drones store: 8-ch PPM encoder
"Quick update... I managed to figure it out. I updated both board with the firmware. One of the boards is on the quad and blinks. I think I still have some inverted channels... but nothing that I can't handle. Thanks a lot for your help."
Jun 16, 2010
Frederic Charpentier commented on Chris Anderson's blog post New product in the DIY Drones store: 8-ch PPM encoder
"Also, just to make sure... The 16Mhz version has a crystal on the board which appears as a metallic rectangle between the CPU and the row of servos solder pads... Is that right?"
Jun 16, 2010
Frederic Charpentier commented on Chris Anderson's blog post New product in the DIY Drones store: 8-ch PPM encoder
"Ok... I got the AVR ISP II and installed the AVR Studio. I think I am ready for that tutorial :-)"
Jun 16, 2010
Frederic Charpentier commented on Chris Anderson's blog post New product in the DIY Drones store: 8-ch PPM encoder
"Ok... So after trying a number of things, I came to the conclusion that I have to reprogram the PPM encoder. I don't have much experience with the Arduino, but I am a software engineer. What would be the easiest solution in terms of an AVR…"
Jun 4, 2010
Frederic Charpentier commented on Chris Anderson's blog post New product in the DIY Drones store: 8-ch PPM encoder
"Chris,
Thanks a lot for taking the time to illustrate this (especially with a video!)... It confirms what I thought. My LED stays solid even when the transmitter is turned on and the receiver light turns to greeen (there is a status LED on the…"
May 29, 2010
Frederic Charpentier commented on Chris Anderson's blog post New product in the DIY Drones store: 8-ch PPM encoder
"Well, honestly, I wish I could worry about the output... The point being that the led is solid blue and if I recall well, it should be blinking when it sees that all the channels are connected and the internal clock is working. I checked that all…"
May 28, 2010
Frederic Charpentier commented on Chris Anderson's blog post New product in the DIY Drones store: 8-ch PPM encoder
"I just purchased 2 PPM encoder boards from DYI Drones. And I am experiencing the same condition as was described by others here. The board is conneced to a Futaba 6008HS FASST receiver. All 8 channels are connected and tested working by connecting a…"
May 28, 2010