Gender
Male
About
About Me:
Multicopter pilot Running DJI Flamewheel 550 hex Alware 2-axiz gimbal GoPro Hero 3 Black
Please tell us a bit about your UAV interest
Will be taking my first UAV with FPV equipment hopefully this weekend if everything goes well.
Hometown:
Port Huron
Activity Feed
We're giving away our 5-foot Keyhole and throwing in a set of Boundary Markers for extra measure! All you have to do is leave your name and email address - and maybe give us a LIKE on the contest entry page. We promise we won't send you junk mail…
"Hey James,
Thanks for the link. I put it in my wish list. I bought the 2-axis version for about $100. It did take about 3 weeks.
Good luck, I'll be watching on the side.
r"
Thanks for the link. I put it in my wish list. I bought the 2-axis version for about $100. It did take about 3 weeks.
Good luck, I'll be watching on the side.
r"
"Can you post the link to that gimbal please. It like the protection it afford the camera and I can't find it on GLB site.
Thanks,
r"
Thanks,
r"
"Well then...you got the good gimbal :). I went the cheap route.
Sorry i can't be of much help.
r"
Sorry i can't be of much help.
r"
"Also, have you looked at the DJI site ti view the videos for the Phantom?"
"Can you provide a link to the gimbal you purchased?I'm not 100% sure, but I don't think you can control the GLB gimbal with the NAZA directly. I know that the DJI ZenMus gimbal is brushless and it will work with the Naza if you use the PMU from DJI…"
"Hello Rick,
In order to add a manual control to point the gimbal down, you will need to hack the board and assign a dail on the radio to control the function. I requires running jumpers from the poins on the board to the rx on you aircraft. there is…"
In order to add a manual control to point the gimbal down, you will need to hack the board and assign a dail on the radio to control the function. I requires running jumpers from the poins on the board to the rx on you aircraft. there is…"
"AHAH!!
Thanks. I feel less dense already.
r"
Thanks. I feel less dense already.
r"
"To Sandy Abernethy: Thank you again, had a chance to futz, but find I am dense. :(
I get where three of the plugs from the three-plug cable go - I think: One to a grd pin of the 2x3 pin set and two go on the top pins of the 2x3 pin set. But where do…"
I get where three of the plugs from the three-plug cable go - I think: One to a grd pin of the 2x3 pin set and two go on the top pins of the 2x3 pin set. But where do…"
"Awesome!! Will futz tonight and see what I get.
thanks Sandy.
r"
thanks Sandy.
r"
"To Hein and Sandy:
Hein, your image of your gimbal board is totally different than mine.
Sandy, Your image of your board is exactly like mine. Did you also get a single cable with three individual female pins on either end? I'm at a loss as to what…"
Hein, your image of your gimbal board is totally different than mine.
Sandy, Your image of your board is exactly like mine. Did you also get a single cable with three individual female pins on either end? I'm at a loss as to what…"
"OOps. I guess so ha."
"Four inputs?? Will this blog allow images?"
"I have a DX7 so I am sort of limited to one 3-position switch and a couple of 2-pos switches. No dials at all. Since the switches are used to control flight functions of the Naza, you could say I'm a few switches short of a full console, but thanks…"
"Yes, kinda sorta. It was not completely level and I wanted to add a little forward tilt to it. - If it ain't broke, right? Regardless I would still like to be able to change some of the settings. It's my nature. Ha."
"I actually was able to re-solder the port onto the board! It is still a little weak, but it does light up and initialize.
Now the hard part begins: Trying to figure out and go through all the steps necessary get the board to talk to the software.…"
Now the hard part begins: Trying to figure out and go through all the steps necessary get the board to talk to the software.…"
