About

Gender

Male


Location

TA


Please tell us a bit about your UAV interest

Arducopters.


Hometown:

TA


Activity Feed

Roi Neustadt posted a discussion
What would be the ideal number of props for the following drone?https://www.youtube.com/watch?v=Hj9UDmWpyks&t=3s
Oct 12, 2019
Roi Neustadt replied to Roi Neustadt's discussion Virtual horizon counter tilt
"Yup - now i understand. Thanks."
Aug 16, 2016
Roi Neustadt posted a discussion
Hello!In Mission planner virtual horizon, when i tilt the drone right the horizon tilts left and when i tilt the drone left the horizon tilts right.What is the reason for that? How can i fix it?
Aug 16, 2016
Roi Neustadt replied to Roi Neustadt's discussion Thanks
"Thanks Peter,
Finally got it right, it's flying nice now.."
May 3, 2016
Roi Neustadt replied to Roi Neustadt's discussion Thanks
"Hello people,i'v changed the frame, props and motors - but kept the entire setup exactly as it was with previous components - but yet, the new drone won't get off the ground.Attached below are pictures of the new drone props setup.Here is the motors…"
May 3, 2016
Roi Neustadt replied to Roi Neustadt's discussion Thanks
"Yes, i'll probably try it in an open area.."
Apr 24, 2016
Roi Neustadt replied to Roi Neustadt's discussion Thanks
"Thanks Cala.
Not very simple, are these fine tuning methods,, "
Apr 24, 2016
Roi Neustadt replied to Roi Neustadt's discussion Thanks
"At last got it right! it's flying! But not yet very precisely..
So first of all: Mossbackfarm, Cala and anyone else who replied - Thanks a lot!Now for the fine tuning issues: Need it to take off as symmetrically as possible and to hover over a…"
Apr 22, 2016
Roi Neustadt replied to Roi Neustadt's discussion Thanks
"Here is the FC i have: PixFalcon Micro PX4 AutopilotI don't seem to find decent documentation.When i connect the 4 motors to channels 1234, where channels 1 is a Futaba with black, red, white wires and channel 4 is blue wire Futaba with only data…"
Apr 22, 2016
Roi Neustadt replied to Roi Neustadt's discussion Thanks
"Here is a video i just took. You can see i am pushing the throttle stick up 3 times - and letting it back down every time - since i already know it ends up in a flip at the direction it starts tilting in the video. That is, i don't want to push the…"
Apr 22, 2016
Roi Neustadt replied to Roi Neustadt's discussion Thanks
"OK - Now that i'v gone through ESC firmware upload again and calibrated the ESC's - all done on the ESC's one by one - i'm kind of lost, since i still get a sideways flipping, instead of a symmetrical take off.
b.t.w the motors all start and speed…"
Apr 22, 2016
Roi Neustadt replied to Roi Neustadt's discussion Thanks
"They don't spin at the same time when the copter is level, one of them starts later. What does it mean? that i need to calibrate the magnetometer again or that i need to calibrate the ESC's again? "
Apr 22, 2016
Roi Neustadt replied to Roi Neustadt's discussion Thanks
"Cala,
Maybe i found out the reason for the problem:
i wonder if i did not calibrate the ESC's well.
i hope that what's described in the following video, which is calibrating the ESC's one by one when not connected to the flight controller, is what…"
Apr 21, 2016
Roi Neustadt replied to Roi Neustadt's discussion Thanks
"Can you please try to help me go step by step - i got a vertigo by now and can't tell heads from tails.."
Apr 21, 2016
Roi Neustadt posted a discussion
Thanks.
Apr 21, 2016
Roi Neustadt posted a discussion
Hello!I am looking for a step by step, for newbies, hardware & software tutorial, which explains the building of the following type of Arducopter (very similar to what this guy did, but without the smartphone…
Feb 13, 2016