Gender
Male
About
Please tell us a bit about your UAV interest
Working on boat drones
Hometown:
Washington DC
Activity Feed
"@Robert, Thank you for the feedback. I had switched the pipeline to videotesrc just to be sure that there was activity. I was aware that would only give me the test screen. When you mention the D3D window, does that open with QT HUD or just when I…"
"I am not sure but would think it is a Bitvise SSH window starting the Raspid"
"Still no luck. I uninstalled and re installed both Qt HUD and Gstreamer.
G-streamer will work great but the HUD is not connecting or starting a pipeline. Here is another message and in this case I have Gstreamer and Qt HUD running."
G-streamer will work great but the HUD is not connecting or starting a pipeline. Here is another message and in this case I have Gstreamer and Qt HUD running."
"Hi Robert, Yes I did go through the blog and looked at that thread. I made no changes to my system and it was working perfectly before so that did not seem to be applicable. I also don't see a specific solution proposed othetr than uninstall and…"
"I have had a setback. I was called away for two weeks and when I tried to run QT HUD I get this.
Mission planner works fine.
I can still get the telemetry and the Gstreamer works independently and will display the telemetry just no video on the…"
Mission planner works fine.
I can still get the telemetry and the Gstreamer works independently and will display the telemetry just no video on the…"
"@Robert,
So you are suggesting that I add this to the code that starts G-Streamer on the Navio? What would the entire code be to start it?"
So you are suggesting that I add this to the code that starts G-Streamer on the Navio? What would the entire code be to start it?"
"Yes I have the Gstreamer at 9000"
"@Robert,
Yes! Success, I had to hit the wireless and let it load for a few. I will be moving forward with my project now and posting some updates. I so appreciate the input for you and Patrick."
Yes! Success, I had to hit the wireless and let it load for a few. I will be moving forward with my project now and posting some updates. I so appreciate the input for you and Patrick."
"Yes Mission Planner is set for 14550 in the connect window.
Because the HUD worked on start-up and during the mission planner boot up, I did not hit the HUD wireless button, but I can try that later tonight. The telemetry definitely cuts off when I…"
Because the HUD worked on start-up and during the mission planner boot up, I did not hit the HUD wireless button, but I can try that later tonight. The telemetry definitely cuts off when I…"
"Yes id did have the -A (it was clipped).
I think I configured the HUD to use 14551 that is what is in the Mavlink connect field"
I think I configured the HUD to use 14551 that is what is in the Mavlink connect field"
"Maybe I could be more descriptive.
I start the G-streamer on the Raspberry & Navio 2
I start the ArduRover with your commands - udp:GCS IP:14550 -C udp:GCS IP:14551 (I put in my IP's)
I start the HUD application
The HUD will start working with a…"
I start the G-streamer on the Raspberry & Navio 2
I start the ArduRover with your commands - udp:GCS IP:14550 -C udp:GCS IP:14551 (I put in my IP's)
I start the HUD application
The HUD will start working with a…"
"Guys I think I got all of the configurations correct, but when I connect Mission planner the telemetry stops feeding to the HUD."
"Patrick & Robert - Thank you for the quick replies. I am going to try Robert's approach first, although I see some great opportunity with the MavProxy approach & video streaming to a larger audience. Quick question how do I change the port to 14551…"
"Hi Patrick
I have been able to get The standalone Gstreamer HUD working, and it is great.
However, I still need the functionality of Mission planner for the GPS map overlay and servo controls. They both listen at the same port: 14550 can that be…"
I have been able to get The standalone Gstreamer HUD working, and it is great.
However, I still need the functionality of Mission planner for the GPS map overlay and servo controls. They both listen at the same port: 14550 can that be…"
