Location
Jakarta
About
About Me:
Build-Fly-Crash-Repeat
Please tell us a bit about your UAV interest
Multirotor
Hometown:
Pangkalanbun
Activity Feed
"30 kgs on quad configuration? You')) need at least 1100 mm quad frame because you'll need @300" kv motors which will spin 32-34" propellers @ 12S LiPo pack.
IMHO, this quad would actually need a lot of cost and by using quad X4 config you'll get no…"
IMHO, this quad would actually need a lot of cost and by using quad X4 config you'll get no…"
"I'm little confused about why description. Is it Ch. 8 identified for Flight Mode or anything?
If you need to remapping channels, just change this parameter, "RCMAP".
Btw, just wanna answer my previous question in case anyone wondering; this mod…"
If you need to remapping channels, just change this parameter, "RCMAP".
Btw, just wanna answer my previous question in case anyone wondering; this mod…"
"You still can control your retractable landing gear on your 3.2.1 FW of APM.
It only use PWM signal from your receiver (if you use PWM mode). But if you use PPM mode receiver, you need to configure analog output (A10-A12) throught Mission Planner as…"
It only use PWM signal from your receiver (if you use PWM mode). But if you use PPM mode receiver, you need to configure analog output (A10-A12) throught Mission Planner as…"
"Bisa dijelaskan lebih rinci apa yg dimaksud dengan "ch.5 sbg ppm input"?
Kalo dari yg saya tangkap, agan mencoba mengubah input ppm dari pin input 1 ke pin input 5 di APM 2.X. Benar begitu?
Parameter apa yang agan ubah?"
Kalo dari yg saya tangkap, agan mencoba mengubah input ppm dari pin input 1 ke pin input 5 di APM 2.X. Benar begitu?
Parameter apa yang agan ubah?"
"So how's your quad now? Still problem?
Landed on this thread because of my colleague have problem too with APM Pro. I think this board were minimalist version of regular board so it kinda confusing.
Considering my previous builds with APM, I see…"
Landed on this thread because of my colleague have problem too with APM Pro. I think this board were minimalist version of regular board so it kinda confusing.
Considering my previous builds with APM, I see…"
"Good tutor Doug.
I helped a friend whom confused about his multirotor and FSi6. When I try access i6's menu Aux Channel, there were only 6 channel and only one switch option.
Do you update your i6 firmware for this tutor? What is your firmware…"
I helped a friend whom confused about his multirotor and FSi6. When I try access i6's menu Aux Channel, there were only 6 channel and only one switch option.
Do you update your i6 firmware for this tutor? What is your firmware…"
"Your quad really stay at low altitude, what a great success! I really adored with your work.
So I assumed you use Pixhawk and I have silly question. Can I do the same with APM 2.6 on f/w 3.2.1? I know that this fc is obsolote but if it can't, what…"
So I assumed you use Pixhawk and I have silly question. Can I do the same with APM 2.6 on f/w 3.2.1? I know that this fc is obsolote but if it can't, what…"
"Hey guys, I need to know if my gimbal config were good.
I use 2 axis alexmos with 2204 260kv motor on roll and pitch.
The camera was Xiaomi Yi that weigh around 70 gr.
The setup I've been use was GoPro setup with these value:
PIDs:
Roll: P = 15; I =…"
I use 2 axis alexmos with 2204 260kv motor on roll and pitch.
The camera was Xiaomi Yi that weigh around 70 gr.
The setup I've been use was GoPro setup with these value:
PIDs:
Roll: P = 15; I =…"
