Please tell us a bit about your UAV interest
Have been hooked since 2009
About
Hometown:
linlöping
Activity Feed
"I have build a v octocopter see this link for more info https://www.rcgroups.com/forums/showthread.php?2768760-Building-Fly..."
"Thank's for fast replies! I run the "git clone https://github.com/diydrones/ardupilot.git" command and after that I run the git checkout Copter-3.3.1 command but it did not work.I get this message: fatal: Not a git repository (or any of the parent…"
"how do you compile copter 3.3.1(I use ubuntu)? I have done as described in :http://dev.ardupilot.com/wiki/building-px4-for-linux-with-make/ .
But that takes the master build.I want to compile a stable version.
The command "git clone…"
But that takes the master build.I want to compile a stable version.
The command "git clone…"
"Thank you Rob for the answer! And sorry for posting here...."
"Hi! I have compile the code(changed some values in v frame) back at end of june.
Now when I configure the copter,I have discover that I have Firmware V3.4-dev(1a9cdac4)(It is written at top of misson planner and in the dataflash logs it is also…"
Now when I configure the copter,I have discover that I have Firmware V3.4-dev(1a9cdac4)(It is written at top of misson planner and in the dataflash logs it is also…"
"I tried to change the code and compile.I did'nt get it to work.I then tried to compile the code using the instructions on this page http://dev.ardupilot.com/wiki/building-the-code/building-px4-with-m... but could'nt make it to compile.
A friend…"
A friend…"
"Ok.Good to know just curios...."
"Thank you Forrest for the compile manual link! I found this old link http://diydrones.com/photo/big-octacopter-v and there
is this image of a v octo
and if i look at the code you added:
}else if( _flags.frame_orientation == AP_MOTORS_V_FRAME ) { //…"
is this image of a v octo
and if i look at the code you added:
}else if( _flags.frame_orientation == AP_MOTORS_V_FRAME ) { //…"
"Can you give any link please,Were I can find any drawing of V octo? I can't find anything about motor number and prop rotation in 3DR docs.regarding v octo.
The only thing I have found regarding v octocopter is this…"
The only thing I have found regarding v octocopter is this…"
"Ok.But how can I know the prop rotation/motor vs servo output?When it is no
image of it? Is it the same as Octocopter image,so I have to think of it in 2 halves?
And Is the Purple field(your motor) in the motor layout section of the spredsheet
you…"
image of it? Is it the same as Octocopter image,so I have to think of it in 2 halves?
And Is the Purple field(your motor) in the motor layout section of the spredsheet
you…"
"I have flashed octocopter to pixhawk and then I selected V in Mandatory-frametype but only
a image of a v quad is visible.No image showing a v octo with prop rotation and which servo ouput
to which motor.So how can I know prop rotation/Motor vs…"
a image of a v quad is visible.No image showing a v octo with prop rotation and which servo ouput
to which motor.So how can I know prop rotation/Motor vs…"
"Forrest, I have little time for the moment,so it can take some time before i have the V octo up and fly...
Do you have the compiling manual ready? It could be nice too see how to do it :).
But I do not want it being trouble for you, if it is a lot…"
Do you have the compiling manual ready? It could be nice too see how to do it :).
But I do not want it being trouble for you, if it is a lot…"
"Thank you Forrest very much for the help and the spreadsheet! I thought that only"ordinary" octocopter was supported and the V was only for V quad?
The prop directions I don't know what is best?
I have not done any compiling but maybe I would give…"
The prop directions I don't know what is best?
I have not done any compiling but maybe I would give…"
"please see drawing"
"I have build a V octocopter and I have a pixhawk.I can't find any setup in misson planner for it
So guess it is not supported? Or is it any motor mixer in latest version?or any links regarding
setup a v octocopter?"
So guess it is not supported? Or is it any motor mixer in latest version?or any links regarding
setup a v octocopter?"
