Gender
Male
About
Location
Taipei,Taipei
Please tell us a bit about your UAV interest
I am a F3A pilot, but I found there are a lot of fun in UAV, they are totally difference, UAV much complicate than F3A and very attractive, I like it.
Hometown:
Astori
Activity Feed
"I had same problem exactly same as Andrew, I have no choice just go back to v0.4, tried back to v0.5 but can't find it."
"Hi, Grey I remember you had pitch problem after you upgrade from v0.5 to v0.7, Now I have same problem as yours tilt 45 degree no move, now you solve your pitch problem can you let me know how to solve this pitch problem? "
"I had same problem as you before, I use 3dr for pc to AT and xBee for AT to MRC, first you can try to uncheck Op resend, if problem still there, try to upgrade your 3dr firmware to Sil 2.x, you can download firmware…"
"your issue 4), your lost telemetry singal shortly you get short tone, then re-connect you get long tone. check your 3dr telemetry"
"I used this tracker since v0.2 and I know telem2 doesn't work and don't use it. I use two pairs radio one pair connect vehicle and pc and one pair for AT and pc, first connect vehicle and pc, then press "CTRL F" pop up a window , Click "mavlink"…"
"I guess what you have is + (P), anyway you can use three different firmware for try, if wrong one used no harm at all, just try another, first one I want try is 'p' version"
"what model do you have a,u,+? if you choice wrong firmware, radio stuck in bootloader mode.
if you have rdf900a or u the latest version is v1.9
if you ahve rdf900+ the latest version is v1.1
please refer rdfdesign.com.au/firmware
The suffix, a,u,p…"
if you have rdf900a or u the latest version is v1.9
if you ahve rdf900+ the latest version is v1.1
please refer rdfdesign.com.au/firmware
The suffix, a,u,p…"
"use configure tool to set up
vehicle 3dr radio
nodeid=0
nodedestination=65536
mavlink=1
nodecount=3
ground station or tracker 3 dr radio
nodeid=1 or 2
nodedestination=0
mavlink=1
nodecount=3"
vehicle 3dr radio
nodeid=0
nodedestination=65536
mavlink=1
nodecount=3
ground station or tracker 3 dr radio
nodeid=1 or 2
nodedestination=0
mavlink=1
nodecount=3"
"v 0.2 is unable to use telem2,, I use two pair 3dr radio, one pair for vehicle, another one pair for tracker, So you have two 3dr radio connect to your mission plan, (two com port), first you have to connect to vehicle then press "Cntl F" pop up a…"
"Hi, Seppo:
I received a pair of RFD900+ and tried to upgrade firmware from v1.11 to v2.3, but no success, and I sent several mail to RFDesign customer support no reply bad service,
following is Modem tool message window, is there anyone here can…"
I received a pair of RFD900+ and tried to upgrade firmware from v1.11 to v2.3, but no success, and I sent several mail to RFDesign customer support no reply bad service,
following is Modem tool message window, is there anyone here can…"
My hex copter just upgrade to 3.2 -dev from v3.12 rc2,I use sbus receiver, but failsafe don’t work, then I use PPM encoder instead of Sbus, work great( same receiver with same failsafe setup), is there anyone has same problem?
"I have the same problem many time, I can't find the reason, attachment is last fly log and tlog, anyone can analysis it and find out the reason.
Thank in advance2013-10-25 13-25 5.log.gpx2013-10-25 12-04-30.tlog"
Thank in advance2013-10-25 13-25 5.log.gpx2013-10-25 12-04-30.tlog"
