Developer

figuring out the Antenna Tracker

3691139590?profile=originalNot many people know but we have an piece of open source software for controlling an Antenna Tracker.  It's been built by Tridge (Arduplane lead developer) for use in the outback challenge.

Sadly we have no documentation and, as far as I know, nobody except Tridge has used it.  Still given Tridge's track record on building great software I suspect it works well and if it doesn't, I'm sure we can fix it.  So to not let this piece of code go to waste, I'd like some help from people who are interested to give it a try and help me figure out how it works.

Here's the little that I know:

  • It runs on any of our supported board (APM1, APM2, PX4, Pixhawk, Flymaple and perhaps VRBrain)
  • For APM1/APM2 users building the code is as easy as opening our hacked ArduinoIDE and selecting File > SketchBook > Tools > AntennaTracker and then building in the normal way.  For PX4/Pixhawk, our autobuilder doesn't automatically build a binary but I can provide one if people are interested.
  • It can control a Pan and Tilt gimbal like this or this found on servocity.com.
  • It may or may not require a GPS
  • It must somehow receive vehicle position updates from the ground station which has the telemetry radio that is connected to the vehicle. Maybe through a USB cable.  Tridge probably uses the python ground station, MAVProxy, to passthrough the vehicle position data to the AT but perhaps we can get MichaelO to build out a similar feature in Mission Planner.
  • I imagine this antenna tracker could also be used to keep a camera focused on the vehicle which might be good for easing the burden on creating videos of our vehicles.

So if you want to give it a try please do and stick any findings, questions or issues below. Alternatively Issues can go into the issues list.

I'll start sticking things into the wiki as they become clear.

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • I¨ve set up Pixhawk as a antenna tracker and use the ReadyMade RC¨s wooden tracker with two servos working great when testing with no power from the Pixhawk. I have a TGY Plush 30A ESC to power the servorail on the Pixhawk, but the servos barely moves when tested from Mission Planner. I use this servos:

    https://hobbyking.com/en_us/turnigy-tgy-sm-8166r-360-analog-metal-g...

    http://www.ebay.com/itm/Rage-RC-S104-16-6VM-Standard-Size-Metal-Gea...

    I just meassured the power from the ESC to be 4.95 volts.

    Should I buy a BEC that uses 5 and 6 volts and power the servos from this and only signal from the PH?

    Jorn

    Turnigy TGY-SM-8166R 360° Analog Metal Gear Robot Servo 33kg / 47RPM / 160g
    Turnigy TGY-SM-8166R 360° Analog Metal Gear Robot Servo 33kg / 47RPM / 160g
  • Randy looks to be busy with the Copter v3.4 release.

  • What happened to Randy?

    Is he working on V1.1?

  • I have never built the code so hopefully someone else will post a solution for you.

  • I'm trying to build it with PX4 Toolchain but with no success yet.

    When I hit "make configure" in PX4 console I get: "make configure is no longer required"

    OK, but there is no config.mk created then..

    then I hit "make apm1" or "make apm2" and get error:

    ../mk/targets.mk:13: *** apm1 is deprecated on master branch; use master-AVR.  Stop.

    Have no idea how to fix it.

    In fact I didn't do clone from github, just copied zip file with ardupilot sources from github and then unziped to local drive. Could it be the problem?

  • Thanks Greg a lot. I really appreciate it.

    Anyway I'm going to study how to open cpp project in Arduino, because afaik it only accepts ino or pde files :-)

  • I found the commit for v0.8.0 in github. Hopefully, it will help.

    Tracker: version to 0.8 and release notes

    Tracker: version to 0.8 and release notes · ArduPilot/ardupilot@752c183
    ArduPlane, ArduCopter, ArduRover source. Contribute to ArduPilot/ardupilot development by creating an account on GitHub.
  • It didn't load pictures with error messages from MP. Anyway the texts are :

    The hex file did no contain an end flag. aborting

    next dialog is:

    Failed to read firmware.hex:No end flag in file

    and last :

    Error uploading firmware

    :-(

    If anybody here has snapshot from GIT of source files of AT 0.8.0 please PM me. I will try to compile it by myself.

    2016-10-24 19_29_53-Mission Planner 1.3.41 build 1.1.6110.31287.png

    2016-10-24 19_34_05-figuring out the Antenna Tracker - DIY Drones.png

    2016-10-24 19_34_19-figuring out the Antenna Tracker - DIY Drones.png

  • Please help,

    I was trying to upload FW 0.8.0 in MP but without success. When I hit "Load custtom firmware", first option which contains also AT 0.8.0, downloading start but after a while I get error message:

    Seems to me like the file is not already there in repo. Is there anybody here listening who can build it again for me?

    For APM1 and APM2?

  • @Randy @Craig thanks for the answer regarding using this with the px4 stack a few months back but I think I not understanding something. If my tracker is communicating via telemetry and has its own GPS why does it matter if my gcs is qgroundcontrol or something that supports px4 natively? Can't I read/write param and telem data with the tracker in the middle or is the issue that the gcs will see the tracker as a ardu device and not px4? I think I'm having a bit of a disconnect here. Thanks a lot. This is a great project and once I can get my auto landing nailed down on arduplane I want to see if I can make the change but creature of habit so far...
This reply was deleted.

Activity

DIY Robocars via Twitter
How to use the new @donkey_car graphical UI to edit driving data for better training https://www.youtube.com/watch?v=J5-zHNeNebQ
Monday
DIY Robocars via Twitter
RT @SmallpixelCar: Wrote a program to find the light positions at @circuitlaunch. Here is the hypothesis of the light locations updating ba…
Nov 26
DIY Robocars via Twitter
RT @SmallpixelCar: Broke my @HokuyoUsa Lidar today. Luckily the non-cone localization, based on @a1k0n LightSLAM idea, works. It will help…
Nov 25
DIY Robocars via Twitter
@gclue_akira CC @NVIDIAEmbedded
Nov 23
DIY Robocars via Twitter
RT @luxonis: OAK-D PoE Autonomous Vehicle (Courtesy of zonyl in our Discord: https://discord.gg/EPsZHkg9Nx) https://t.co/PNDewvJdrb
Nov 23
DIY Robocars via Twitter
RT @f1tenth: It is getting dark and rainy on the F1TENTH racetrack in the @LGSVLSimulator. Testing out the new flood lights for the racetra…
Nov 23
DIY Robocars via Twitter
RT @JoeSpeeds: Live Now! Alex of @IndyAChallenge winning @TU_Muenchen team talking about their racing strategy and open source @OpenRobotic…
Nov 20
DIY Robocars via Twitter
RT @DAVGtech: Live NOW! Alexander Wischnewski of Indy Autonomous Challenge winning TUM team talking racing @diyrobocars @Heavy02011 @Ottawa…
Nov 20
DIY Robocars via Twitter
Incredible training performance with Donkeycar https://www.youtube.com/watch?v=9yy7ASttw04
Nov 9
DIY Robocars via Twitter
RT @JoeSpeeds: Sat Nov 6 Virtual DonkeyCar (and other cars, too) Race. So bring any car? @diyrobocars @IndyAChallenge https://t.co/nZQTff5…
Oct 31
DIY Robocars via Twitter
RT @JoeSpeeds: @chr1sa awesomely scary to see in person as our $1M robot almost clipped the walls as it spun at 140mph. But it was also awe…
Oct 29
DIY Robocars via Twitter
RT @chr1sa: Hey, @a1k0n's amazing "localize by the ceiling lights" @diyrobocars made @hackaday! It's consistently been the fastest in our…
Oct 25
DIY Robocars via Twitter
RT @IMS: It’s only fitting that @BostonDynamics Spot is waving the green flag for today’s @IndyAChallenge! Watch LIVE 👉 https://t.co/NtKnO…
Oct 23
DIY Robocars via Twitter
RT @IndyAChallenge: Congratulations to @TU_Muenchen the winners of the historic @IndyAChallenge and $1M. The first autonomous racecar comp…
Oct 23
DIY Robocars via Twitter
RT @JoeSpeeds: 🏎@TU_Muenchen #ROS 2 @EclipseCyclone #DDS #Zenoh 137mph. Saturday 10am EDT @IndyAChallenge @Twitch http://indyautonomouschallenge.com/stream
Oct 23
DIY Robocars via Twitter
RT @DAVGtech: Another incident: https://t.co/G1pTxQug6B
Oct 23
More…