PixRacer with Ardupilot

Replies

Mark Whitehorn December 10, 2017 at 8:30am

https://store.mrobotics.io/product-p/auav-acsp5-mr.htm

AUAV Power Module (ACSP5) 10S-LIPO
Wixi December 9, 2017 at 10:57pm

Michael, could you as yet source the ACSP5 power module ?

I don't seem to be able to source it...
Juan C Ricardo October 10, 2017 at 5:03pm

Hi guys:

Anyone knows here if I can wire an analog speed sensor to pixracer ?

regards and thanks in advance !

jc
Emanuele Tonucci October 6, 2017 at 1:04pm

Thank you very much.

I'll try tomorrow!

Hope the weather will be clement!

Luc Maximilien said:

Autotuning works pretty well , run one axis separately and you will have a good result
Luc Maximilien October 6, 2017 at 12:41am

Autotuning works pretty well , run one axis separately and you will have a good result
Emanuele Tonucci October 3, 2017 at 12:15pm

Thank you for your reply.

I knew the video, but it is no so simple to do it!

If I have a decent set of PID I can enable the AutoTune mode.

Or if it is possible to convert the PX4 PID to Arducopter PID the problem will be solved!

If somebody know this possibility it will be very appreciated.

thanks to all

Otto Küng said:

Try this methode, it works verry well without risk and is rapid.

https://www.youtube.com/watch?v=aq1jXHMiJgg&feature=youtu.be
Otto Küng October 3, 2017 at 2:36am

Try this methode, it works verry well without risk and is rapid.

https://www.youtube.com/watch?v=aq1jXHMiJgg&feature=youtu.be
Emanuele Tonucci October 3, 2017 at 2:18am

Hello to all,

I built a Robocat 270 with Pixracer and Emax 2205 and propellers 5045.
By charging PX4 with ZMR250 configuration, the drone flies decently.
However, I would like to go to Ardupilot because it is the platform I know best.
Unfortunately, with default PIDs, the drone flies very badly, but it is almost impossible to take off.
What PIDs I could try to have at least the ability to activate auto tune?
Thank you
Jean-Marie PRIGENT September 13, 2017 at 9:25am

@Phillip Kocmoud : don't know where to ask because of http://auav.com/contact.php not functionnal (impossible to submit question > 'bad format' on email field for a valid email! ). For now, European customer must buy

For now, European customer must buy there Pixracer on mRO (exact ?) ? Thats mean must pay shipping cost from US to France + customs (= approx 60$ at minima)? I didn't find any distributor of your Genuine board here.

I try to make an order on mRO to see if there are some options for europe but stopped on shipping cost...
Serg Bokh August 4, 2017 at 2:18am

Hi there,

I used to supply my PixRacer via my 4-in-1 ESC 5v UBEC.

But within ArduCopter log it is 4.6v. Meassuring by multimeterat it is 4.8v. The only good thing is that the voltage level is stable.

- Have read many times that it is important to keep 5v. But what are the actual possible promlems if my voltage is about 4.8-4.6 volts?

- Is that converter suitable to supply Pixracer? Mini DC Voltage Step-Down Regulator (D-SUN)

of 120

Discussions

PixRacer with Ardupilot

Replies

Activity