Gender
Male
About
Location
Brest
Please tell us a bit about your UAV interest
Like everything around Arduplane. APM25, ezuhf, diversity, TBS Caipirinha, FX61, MiniZ, SuperSkySurfer 2000. Long range flying. Tunning Dronecell, raspberryPi,PiCamera, Attitude SD Mod, Ardustation Mega Antenna tracker
Hometown:
Brest
Activity Feed
"@Andrew Tridgell
following this answer from you
"If you need NMEA on an APM1 or APM2 then let me know and I can show you which line of code to change to add it back it for your own build.
Cheers, Tridge"
Hi, I would like to reactivate NMEA in…"
following this answer from you
"If you need NMEA on an APM1 or APM2 then let me know and I can show you which line of code to change to add it back it for your own build.
Cheers, Tridge"
Hi, I would like to reactivate NMEA in…"
"@Phillip Kocmoud : don't know where to ask because of http://auav.com/contact.php not functionnal (impossible to submit question > 'bad format' on email field for a valid email! ). For now, European customer must buy
For now, European customer must…"
For now, European customer must…"
"@fernando : for what I know only firmware PX4 1.5.5 is working. Last versions have no RC response. "
"Sorry for late answer Patrick. Thanks very much. I remember your post now.
As far as I know, TBS Crossfire is now the only compact Long Range solution that transmits Mavlink and RC with DYNAMIC bandwidth and avoids all the complexity of another link…"
As far as I know, TBS Crossfire is now the only compact Long Range solution that transmits Mavlink and RC with DYNAMIC bandwidth and avoids all the complexity of another link…"
"Hi Patrick, could you please share more infos on this or link ? Seems very interesting and definitly more simple than AR"
"@Hein du Plessis ! yes wires are pain in compact setup...only miss a 'clever' wire distribution board and it will be easier for everyone. "
"If some people are looking for a 3d printed support for the pixfalcon, I made a 3d support with dampers for the Pixfalcon (v1).
Hope it could help some people: https://www.thingiverse.com/thing:2348176"
Hope it could help some people: https://www.thingiverse.com/thing:2348176"
"lol my pleasure to help you Michal. Honestly I don't understand why there is so few people using this playuav osd depsite the fact it's a really really good alternative to the BIG font of minimosd. Moreover, form factor is good and STM32…"
"hi,
You've got 4 wires for telemetry ? Have you try to force "Telemetry" from mission planner in initial setup/ optional hardware /osd ? > just clik on 'minimosd picture'.
If you have got a FTDI you can try to output telemetry feed with ctrl+F,…"
You've got 4 wires for telemetry ? Have you try to force "Telemetry" from mission planner in initial setup/ optional hardware /osd ? > just clik on 'minimosd picture'.
If you have got a FTDI you can try to output telemetry feed with ctrl+F,…"
"hi
1/ Try to reverse rx and tx
2/ check telemetry serial speed in playuav config tool AND mission planner"
1/ Try to reverse rx and tx
2/ check telemetry serial speed in playuav config tool AND mission planner"
"I'm sorry I'm not sure about blue light. I must check this after work.
Perhaps you could look at my video at 0.15 min : https://youtu.be/K_rhIYWg0L0 to check wires."
Perhaps you could look at my video at 0.15 min : https://youtu.be/K_rhIYWg0L0 to check wires."
"Are you sure telemetry is correctly plugged ?
- for video you must have (from left to right) wires on :1,2 (in) and 5,6 (out)
- for telemetry (from left to right) wires on : 1 (blk),6 (green) 7 (blue) 8 (red)
>>> if you not apply power to…"
- for video you must have (from left to right) wires on :1,2 (in) and 5,6 (out)
- for telemetry (from left to right) wires on : 1 (blk),6 (green) 7 (blue) 8 (red)
>>> if you not apply power to…"
"Hi,
Like you see on my screenshot above, you right : you must have osd display (without signal input).
But you say "I can't get any video" - for me OSD is not video - it's only osd.
Some people have pb with 1st generation Playuav board with…"
Like you see on my screenshot above, you right : you must have osd display (without signal input).
But you say "I can't get any video" - for me OSD is not video - it's only osd.
Some people have pb with 1st generation Playuav board with…"
"Hi,
Default video IN is VIDEO 2 IN and VIDEO 2 GND and not Input 1 (signal and gnd) !
It's 1st and 22nd plug from left to right
look here http://www.playuav.com/wiki/doku.php?id=projects:playuavosd:hardware.
hope it help ! "
Default video IN is VIDEO 2 IN and VIDEO 2 GND and not Input 1 (signal and gnd) !
It's 1st and 22nd plug from left to right
look here http://www.playuav.com/wiki/doku.php?id=projects:playuavosd:hardware.
hope it help ! "
"this is better to use data feed inside RC link like in UltimateLRS and it's works really well.
http://www.itluxembourg.lu/site/ultimate-lrs-wiring-diagram/
and dedicated forum here :
http://www.rcgroups.com/forums/showthread.php?t=2037442"
http://www.itluxembourg.lu/site/ultimate-lrs-wiring-diagram/
and dedicated forum here :
http://www.rcgroups.com/forums/showthread.php?t=2037442"
"jDrones has started 2 years ago an antenna tracker that never arrive...
Ardustation mega was forgive to.
Lot of people have tweak the MFD antenna tracker.
I understood that guys from Quantracker with VBI and PlayUAV-OSD project are working on a…"
Ardustation mega was forgive to.
Lot of people have tweak the MFD antenna tracker.
I understood that guys from Quantracker with VBI and PlayUAV-OSD project are working on a…"
