Gender
Male
About
Location
Selangor
About Me:
Multirotor and FPV addict now!
Please tell us a bit about your UAV interest
I just want to have fun. And fun becomes my bread and butter now.
Hometown:
Malaysia
Activity Feed
"Hey Aran, mine have similar issue and it's a Crius' Mavlink OSD, below steps work for me especially if it's a Crius one, very fussy, so whoever saw this today, hope this helps.
1. Use arduino IDE to clear the EEPROM first- download from…"
1. Use arduino IDE to clear the EEPROM first- download from…"
"Hey guys, I recently got this CRIUS Mavlink OSD that I have problem with the fonts like they are snowing, wasted 2 days till i found the review on banggood. Step by step that works for me as below,
1. Use arduino IDE to clear the EEPROM first-…"
1. Use arduino IDE to clear the EEPROM first-…"
"Hi Raph,
It's normal that Y6 has a rather bad flight time. My spec,Y6 with Sunnysky 800kv
Turnigy 4S 5000mah or Zippy 2x 4S 3000mah
APC 11x4.7 props
AUW 2.92kg
HBK low voltage lipo buzzer default at 3.3V
Flight time btw 7min to 8mins. A Y6 compare…"
It's normal that Y6 has a rather bad flight time. My spec,Y6 with Sunnysky 800kv
Turnigy 4S 5000mah or Zippy 2x 4S 3000mah
APC 11x4.7 props
AUW 2.92kg
HBK low voltage lipo buzzer default at 3.3V
Flight time btw 7min to 8mins. A Y6 compare…"
"Hi Randy,
Here's my experience with the APM2.5 + PM on 2.9.1b.
I had RTL fly away on 2.9.1b which was due to PDB inteference. The following solved it,
1) reallocate PDB interference
2) manually enter declination
3) compass live calibration
4)…"
Here's my experience with the APM2.5 + PM on 2.9.1b.
I had RTL fly away on 2.9.1b which was due to PDB inteference. The following solved it,
1) reallocate PDB interference
2) manually enter declination
3) compass live calibration
4)…"
"Hey i had similar issue earlier.
I think i was on 2.9.1, with apm 2.5 + PM, a Y6 with 800kv sunnysky, F30 simonk flashed esc, th9x.
Activated the A10 and A11 for gimbal, using BMS analog servo. First test, it doesn't work. The servos just wouldnt…"
I think i was on 2.9.1, with apm 2.5 + PM, a Y6 with 800kv sunnysky, F30 simonk flashed esc, th9x.
Activated the A10 and A11 for gimbal, using BMS analog servo. First test, it doesn't work. The servos just wouldnt…"
"Hey guys,
Can anyone help me read on my log whether my vibration dampening is good?
It has now 3 layers(previous 2) of dampening but still my loiter is bouncing around in the wind. Stab is all fine.
Can't be sure which is the right file i should…"
Can anyone help me read on my log whether my vibration dampening is good?
It has now 3 layers(previous 2) of dampening but still my loiter is bouncing around in the wind. Stab is all fine.
Can't be sure which is the right file i should…"
"Hey guys,
I just upgraded to 2.9.1b because my Alt hold sort up going up and down, and my loiter is bouncing around itself even if just a light wind. Stablizer mode is completely fine.
When no wind, it's completely fine. But often it would suddenly…"
I just upgraded to 2.9.1b because my Alt hold sort up going up and down, and my loiter is bouncing around itself even if just a light wind. Stablizer mode is completely fine.
When no wind, it's completely fine. But often it would suddenly…"
