Gender
Male
About
Location
VIC
Please tell us a bit about your UAV interest
Enjoy the challenge of UAV
Hometown:
Melbourne
Activity Feed
"Hi all,
Trying to load Rc11 (and RC10 for that matter) with APM Planner onto my pixhawk (non 3DR version) I haven't had any issues loading firmware in the past but now I can't get past the status showing "Requesting CoA" ...It won't load stable…"
Trying to load Rc11 (and RC10 for that matter) with APM Planner onto my pixhawk (non 3DR version) I haven't had any issues loading firmware in the past but now I can't get past the status showing "Requesting CoA" ...It won't load stable…"
Hi all,Trying to load latest Arducopter onto my pixhawk (non 3DR version) I haven't had any issues loading firmware in the past but now I can't get past the status showing "Requesting CoA" ...has anyone had any issues with this?…
"Any thread title that begins with "The truth...." is always going to be a great one! Sounds a bit like a click bait story..."This guy started using Simonk ESC's with a low KV motor and you'll never believe what happened next..."
On a more serious…"
On a more serious…"
"HAHA So good!"
"I changed to -g 10 and ended up with a lot less artifacts happening
With -g 10 a big delay built up. Up to about 5 secs after 5mins.
I tested without the quad's TX running and got a lot better range and quality so UHF will be a great addition
I also…"
With -g 10 a big delay built up. Up to about 5 secs after 5mins.
I tested without the quad's TX running and got a lot better range and quality so UHF will be a great addition
I also…"
"Half way there - just need a connector to hook it up. Also some of that RG402 semi flex cabling would be nice..."
"Cheers Maulkans - I'll fire up the soldering iron and make some! "
"Thanks Martin, I've changed the settings. I'll let you know how it goes. I quickly benchtested the video and when I first started it up it was lagging by a few seconds but it soon settles to around ~200ms after 30secs or so..."
"Did first test flight today. Worked pretty well when very close to the ground and within 15m's or so.
The setup:
Alien H4 Pixhawk with Frsky 2.4Ghz TX/RX
Video TX WN722 w standard omni
Video RX WN722 w standard omni
Wifibroadcast setup Ch7…"
The setup:
Alien H4 Pixhawk with Frsky 2.4Ghz TX/RX
Video TX WN722 w standard omni
Video RX WN722 w standard omni
Wifibroadcast setup Ch7…"
"Merica!!! Luckily he had the right to bear arms to protect himself from the drone....
Good on you Joe for taking it to him. What a loose canon!"
Good on you Joe for taking it to him. What a loose canon!"
"All fixed - silly mistake! Wasn't in the wifibroadcast directory so the .rx/ command wasn't working. CD $wifibroadcast fixed it for anyone else in same boat. Test flight soon!
Any progress on OSD??"
Any progress on OSD??"
"Hi all, I've got the link working between 2 Pi's but it's not overly practical as I have a laptop with the latest Ubuntu and I don't have a screen to use in the field with the Pi.
I've having trouble getting the streamgoing with gstreamer:…"
I've having trouble getting the streamgoing with gstreamer:…"
"Ditto on this point - could someone break this down for the linux/RPI amateurs! Thanks :)"
"Decided to change to Open LRS 433MHz to free up the 2.4GHz band. I've just picked up 2 TP-Link 722's - will test out tonight and let everyone know how they go - does anyone know if the images posted on the dropbox account from page 6 have the kernel…"
"No such thing as too much detail Randy! :P"
"If you're using a Pi2 that could be the issue. I had the same problem. The images were made with a Pi A/B. I got around it by booting the SD card in a Pi 1 - updating then I could run the image on my Pi2.
A good explanation is here:…"
A good explanation is here:…"
