About

Gender

Male


Location

Q.C.


About Me:

I'm a computer engineering student=p I'm really into aircrafts and stuff=p


Please tell us a bit about your UAV interest

Well ever since I was in elementary, aircrafts really fascinate me. I was suppose to enter flying school had it not been for my oh-so-protective mom=)) So the next best thing is... taadaaa! UAV with FPV flight=p God sent answer to frustrated pilots like me haha=))


Activity Feed

Jonathan Diaz replied to Johann Van Niekerk's discussion Ublox LEA 5H module still working with current APM 2.5 ?
"I don't know if it would still matter after all these years but.. yeah it still works on apm 2.5. I just upgraded its firmware and flashed it with the config file for apm use. I used my old ublox lea5h from like 6 years ago as it was way better than…"
Jan 14, 2016
Jonathan Diaz replied to Jonathan Diaz's discussion IMU lacks solder blob on 3 indicated locations..
"I see, haha I guess I missed it on the wiki of the apm, it was also there. Anyway thanks for the replies guys :)"
Nov 6, 2011
Jonathan Diaz posted a discussion
We got a new IMU board as we've become skeptic of the data coming out of our previous IMU . Anyway, we've noticed that on our old imu, these 3 points lack a solder blob on them, whereas on our new IMU, it had solder blobs on them. I wonder if the…
Nov 5, 2011
Jonathan Diaz posted a discussion
Hi guys well apparently my board seems to have a fried mux. I salvaged a working 328p from my 1280 board and the now the ppm led lights up already and I can see the pwm getting in already through the CLI. But unfortunately there's no output; I mean…
Oct 31, 2011
Jonathan Diaz replied to Aqntbghd's discussion No radio input, is it a fried Mux ?
"Hi guys well apparently our board (marianne is my groupmate) seems to have a fried mux. I salvaged a working 328p from our 1280 board and the now the ppm led lights up already and I can see the pwm getting in already through the CLI. But…"
Oct 31, 2011
Jonathan Diaz replied to basshead's discussion A solution to weird gyro drifting and stuff
"Nice! hmm did your horizon jump around before you throttled up or did it only start after throttling up? we're having the same problem but we're leaning on vibrations. Anyway will try this later
 "
Oct 13, 2011
Jonathan Diaz commented on Toby Mills's blog post What is the maximum range of an Xbee? - Lets find out...
"Rigel,we tried unbricking them but to no avail. Before we were successful in unbricking with the first xbee for like two or three times but after that it went dead. With the second xbee, unbricking didn't worked at all."
Oct 12, 2011
Jonathan Diaz commented on malcolm churn's blog post ACM Loiter (GPS) Hold Traditional Helicopter
"aw I see! Thanks randy!"
Sep 4, 2011
Jonathan Diaz commented on malcolm churn's blog post ACM Loiter (GPS) Hold Traditional Helicopter
"great flight! hmm did you use an external gyro for yaw? or did you just use the apm?"
Sep 3, 2011
Jonathan Diaz posted a discussion
Good day guys,I'm having a dilemma with our ACM. I loaded the acm rc2 code and tried moving the heli to see if it responds when I move it in stable mode. Well it didn't:( Only the rudder countered the movements. I thought I just forgot to turn on…
May 6, 2011
Jonathan Diaz replied to Jonathan Diaz's discussion APM Brown-outs
"Thanks for the feedback guys!=D
 
Andres,
 
Hmm Ok I'll try to power the apm then with a 2s lipo on the corresponding pins.
 
Sebastian,
Ok I'll also check my ubec as well
 
Martint,
Its v1.0"
Apr 10, 2011
Jonathan Diaz posted a discussion
  Good day guys, hope you can shed some light on this..  I think I blew the outputs of my APM. The mux led doesn't light up when I power it up through the the rc's ubec  and it doesn't receive my rc input and the leds aren't that bright.  However,…
Apr 6, 2011