Location
Hamburg
About
About Me:
Nerd
Please tell us a bit about your UAV interest
//Want to equip my TS II with RTL// done //Want to build a stable copter platform for aerial photography.// done Learn to fly without using "Loiter or RTL"
Hometown:
Hamburg
Activity Feed
"If EKF and EK2 both are enabled and AHRS_EKF==2 then arming works."
Hi.My quad is on Pixracer and 3.4.dev from yesterday. I can't arm the motors.pre arm checks are off.What does "waiting for nav checks" mean?Yesterday with 3.3.4 it flew in manual mode.
Hi all.Due to a mechanical motor problem I want to change my flat hexa to a quad temporarily.I am running FW 3.1.2 on a pixhawk.I removed two motors and ESCs. The frame stayed the same, but mechanical configuration now is as quadro.Do I have to…
"Hi, thank you very much for your calculation. Yes, I think you are absolutely right. I mentioned earlier, that due to the different thrust of the back motors, the calc of CG is difficult, but I actually meant CT.
I followed a calculation posted here…"
I followed a calculation posted here…"
"Thanks for the fine video. You're a pro!
I'm glad to see you got it tuned in! Your quad flies nice now.
I have the same problems with the CG. Should be under the Flightcontrol, but the two back arms deliver slightly less thrust than they weigh, due…"
I'm glad to see you got it tuned in! Your quad flies nice now.
I have the same problems with the CG. Should be under the Flightcontrol, but the two back arms deliver slightly less thrust than they weigh, due…"
"The programming mixes should be fine and should't affect the 4 Stick Channels, they are on aux.
But I would check the radio within the mission planner software wether the throttle, yaw, roll, pitch are on the correct channels and wether the range is…"
But I would check the radio within the mission planner software wether the throttle, yaw, roll, pitch are on the correct channels and wether the range is…"
"Did you do a radio calibration?
I had some trouble with it when moving from APM to pixhawk, since pixhawk uses sum Receiver. The channels where mixed up.
You could check this, too.
(Last idea ;-))"
I had some trouble with it when moving from APM to pixhawk, since pixhawk uses sum Receiver. The channels where mixed up.
You could check this, too.
(Last idea ;-))"
"Yes, this setup is exactly right.
If you have done the ACC calibration once, there should be nio Problem with it.
Try to start with stabilize first. When compass is not calibrated exactly, there are Problems with loiter.
In stabilize, Motors have to…"
If you have done the ACC calibration once, there should be nio Problem with it.
Try to start with stabilize first. When compass is not calibrated exactly, there are Problems with loiter.
In stabilize, Motors have to…"
"You're welcome!
I think the spinning direction is already done right. Its shown here:
http://copter.ardupilot.com/wiki/initial-setup/assembly-instruction...
for Iris or X-Quad.
In your first post you wrote:
1) Motor setup (TGY 28-26 1200kv): #1 is…"
I think the spinning direction is already done right. Its shown here:
http://copter.ardupilot.com/wiki/initial-setup/assembly-instruction...
for Iris or X-Quad.
In your first post you wrote:
1) Motor setup (TGY 28-26 1200kv): #1 is…"
Hi all,I'm having a strange issue over months: My tricopter spirals down in midflight, often after flying a circle.Often it does two spirals and comes back to normal flight, sometimes it spirals down. Sometimes the receiver failsafe warning goes…
Hi all,I would like to change the setup on my brave APM 1.4 which has guided my old twinstar up to now. I now want to bring it to live in a different plane and would need to know where to connect OSD and telemetrie and all that nice stuff.Is there a…
"Hi,
Did you encounter any problems Other than the sounds? Actually my sounds are still there and I haven't flown it yet. Did yours ever fail in midflight or did it fly safely?"
Did you encounter any problems Other than the sounds? Actually my sounds are still there and I haven't flown it yet. Did yours ever fail in midflight or did it fly safely?"
"Hi. This definitely was an issue with the "teaching of all esc at once".
After a new teaching procedure of every esc individually the problem is gone."
After a new teaching procedure of every esc individually the problem is gone."
