About

Gender

Male


Please tell us a bit about your UAV interest

Arduplanes and Arducopters are my passion.


Hometown:

Vienna


Activity Feed

Mark Van Haze posted a discussion
https://www.amazon.com/b?tag=skim1x164751-20&node=8037720011Int... design choice. What are the coolers for?Amazon Prime Air_Private Trial_Ground-HIGH RES (Large).png
Dec 14, 2016
Mark Van Haze replied to Tom Kopp's discussion Pixhawk with low KV motors unstable/crash
"I use 330KV Tmotors on Afro ESCs from HK on a 4Kg quad and there are no issues. I ran autotune with the recommended reduction in frequency (see the ardu manual for that) and it all works nicely."
Nov 28, 2016
Mark Van Haze replied to Jubal Ragsdale's discussion 3.1 Autotune won't engage
"I had the same problem. What you need to do is fly in ALt hold AND make sure your throttle is around 50  percent or lower while hovering. "
Nov 14, 2016
Mark Van Haze replied to Jeremy Stromsoe's discussion APM Joystick Questions, Channels 9-12?
"I would also like to know how to do that. Anybody?"
Jul 13, 2016
Mark Van Haze replied to L's discussion Pixhawk OK in Loiter, flies off wildly in Stabilize in ArduCopter User Group
"Thanks for the explanation. On a copter where there is just too much electronic interference, could I fly using a Nav mode with GPS only?"
Jun 14, 2016
Mark Van Haze commented on Damian's blog post Another Drone KickStarter bites the dust ....
"I was wondering about how and when gimbals will be replaced for some time now and at least get to the point where we can have 1080p electronically stabilized. My knowledge is limited here but could somebody explain how these guys are doing it and…"
Jun 14, 2016
Mark Van Haze replied to L's discussion Pixhawk OK in Loiter, flies off wildly in Stabilize in ArduCopter User Group
"Just a question since you probably can help me with this: When is the compass used and how/for what?"
Jun 14, 2016
Mark Van Haze replied to Mark Van Haze's discussion Swash plate angle question
"Thanks!"
Feb 8, 2016
Mark Van Haze posted discussions
Feb 7, 2016
Mark Van Haze replied to befinitiv's discussion 3+km HD FPV system using commodity hardware
"Hello Wolke,

How do you intend to transmit the stream using this E12 board?"
Feb 5, 2016
Mark Van Haze replied to Mark Van Haze's discussion Geofence bug in Mission Planner
"I did some further testing and it t"
May 14, 2014
Mark Van Haze posted a discussion
I believe I found a small bug in the current MP version concerning the geofence.If you set up an area via polygons in the planner followed by placing the return point, my Arduplane (also current version) on a fence breach, will happily leave in…
May 13, 2014
Mark Van Haze replied to Mark Van Haze's discussion Kerosene jet with Arduplane crash analysis
"Hi,

thank you very much for looking into our case. We struggled a lot with the EMF noise induced via ECU and its engine on this airframe. Due to this we turned compass learning off. During the flight we had no radar systems switched on yet, so as…"
Apr 13, 2014
Mark Van Haze replied to Mark Van Haze's discussion Kerosene jet with Arduplane crash analysis
"It's for testing a radar prototype for our university. The flying area is a dedicated area for this purpose and there are failsafes for the motor Ecu that are triggered should there be any indication of a fly away."
Apr 13, 2014
Mark Van Haze posted a discussion
For a project that involves fast, low flying jets, we set up an APM running Arduplane 2.74.We used EZUHF for the RC link which was programmed to trigger RTL if the RC link got too weak or lost.What you can see in this video is the Mavlink data using…
Apr 13, 2014