Gender
Male
About
Location
Chennai
About Me:
Founder, Aero360
Please tell us a bit about your UAV interest
Interested to learn more about UAV / Drones for providing Drone Surveying Mapping and Inspection Services.
Hometown:
Chennai
Activity Feed
" TEST FLIGHT - 3
Description:
Pre Flight Checklist checks done.
Flight checked for FBWA mode and its performance to the same.
Take Off done at FBWA mode by Hand Launch. (Refer…"
Description:
Pre Flight Checklist checks done.
Flight checked for FBWA mode and its performance to the same.
Take Off done at FBWA mode by Hand Launch. (Refer…"
" TEST FLIGHT - 2
Description:
Pre Flight Checklist checks done.
Flight checked for FBWA mode and its performance to the same.
Take Off done at FBWA mode by Hand Launch.…"
Description:
Pre Flight Checklist checks done.
Flight checked for FBWA mode and its performance to the same.
Take Off done at FBWA mode by Hand Launch.…"
" TEST FLIGHT -1
Description:
Pre Flight Checklist checks done.
Flight checked for FBWA mode and its performance to the same.
Take Off done at FBWA mode by Hand Launch. (Refer…"
Description:
Pre Flight Checklist checks done.
Flight checked for FBWA mode and its performance to the same.
Take Off done at FBWA mode by Hand Launch. (Refer…"
"Hi Rodrigo,
We chose X8 cuz of the performance it will give in terms of speed and flight time, also the spacious fuselage is one of the reason as we can experiment with more components/payloads.
We get the telemetry data in our Ground station during…"
We chose X8 cuz of the performance it will give in terms of speed and flight time, also the spacious fuselage is one of the reason as we can experiment with more components/payloads.
We get the telemetry data in our Ground station during…"
"Hi Rodrigo,
Actually the purpose of going for custom built drone is to improve the accuracy of the results by adding RTK/PPK GPS in future and also to increase the flight time for more area coverage.
Keep following my posts and do recommend me on…"
Actually the purpose of going for custom built drone is to improve the accuracy of the results by adding RTK/PPK GPS in future and also to increase the flight time for more area coverage.
Keep following my posts and do recommend me on…"
" 15) Problem With Airspeed Sensor
Again same GPS issue occurred. This time we checked with the components connected to Autopilot.
If Airspeed sensor is connected to the circuit GPS is not powering. If Airspeed Sensor is removed from…"
Again same GPS issue occurred. This time we checked with the components connected to Autopilot.
If Airspeed sensor is connected to the circuit GPS is not powering. If Airspeed Sensor is removed from…"
"Discussion continues with connections check...
9K) Connections Checks
Checked whether above mentioned connections are done perfectly before Connecting from battery to Power module
Started from Install firmware to the Autopilot by connecting…"
9K) Connections Checks
Checked whether above mentioned connections are done perfectly before Connecting from battery to Power module
Started from Install firmware to the Autopilot by connecting…"
"I am continuing the discussion with connections of components...
9J) Purpose of Y-cable connection
a) Connection between ESC and Servo (to power servo)
b) Connection between ESC and Autopilot (to send throttle signal to ESC-motor)
c) Connection…"
9J) Purpose of Y-cable connection
a) Connection between ESC and Servo (to power servo)
b) Connection between ESC and Autopilot (to send throttle signal to ESC-motor)
c) Connection…"
"Fabrication process finished and followed by that placement of components as follows
9. Placing components in Airframe Fuselage compartments
a) Weightless foam pieces were stuck using hot glue gun at the fuselage bottom part compartments to level…"
9. Placing components in Airframe Fuselage compartments
a) Weightless foam pieces were stuck using hot glue gun at the fuselage bottom part compartments to level…"
"I am continuing my fabrication process.
Please suggest me if anything needs changes or modifications
Airframe
Checked for all Parts
Pair of Wings with Elevons and Wing joiners
Fuselage top and bottom parts
Canopy
Two Carbon Rods to Strengthen…"
Please suggest me if anything needs changes or modifications
Airframe
Checked for all Parts
Pair of Wings with Elevons and Wing joiners
Fuselage top and bottom parts
Canopy
Two Carbon Rods to Strengthen…"
Am looking for building a Fixed Wing UAV for Aerial mapping and performing it based on my own research. Your suggestions are most welcome to correct myself in building it. AIMTo assemble a Fixed wing UAV for Aerial Mapping with 2.5 - 3 hours…
