Comments

• 3D Robotics

  Chris Anderson November 12, 2011 at 10:18pm

  Adil: Set one of your toggle switch modes to Loiter. Wait for GPS lock, then fly and switch into Loiter at the position you want to hold.
• 

  Adli Shahnaz November 12, 2011 at 10:09pm

  Hello all.

  Can somebody help me step by step on how to set the gps hold. Thank you in advance.

   
• 

  brett binnekade November 9, 2011 at 10:13am

  Is it important to mount the board directly in the center of a quad frame or can it be slightly off to the side. I would like to mount mine about 2 or 3cm off center.
• 3D Robotics

  Chris Anderson November 9, 2011 at 6:56am

  Tom: that just means that your throttle is reversed on your RC transmitter (maybe you've switched to another model memory?). Switch it and go through the MP radio setup again.
• ahmed hakeem November 9, 2011 at 12:33am

  hello i m new  in this Group ..also at this quadcopter ..

  i receive my ArduCopter Quad v1.1 RTF - i m locking for some one can help me how to fly i have JR-PCM9X but there is no program with this remote only i find :

  http://diydrones.com/profiles/blogs/how-to-program-6-flight-modes

  this is different model of my remote by the Options ..

  if i want to START connect ...

  1- which mode i should use airplane or heli ??

  2- what is the revers and north ??

  3- what should i do in travel adjust ??

  4- what should i do in Flap ??

  5- what should i do in program Mix i have 1,2,3,4,5,6

  6- how can i use the position hold ??

  7- how can i use the GPS ??

  sorry about this all but really i need help to fly my new babe :)  

  Thank For all ...
• Moderator

  Michael Pursifull November 7, 2011 at 8:12am

  See flybrushless.com for other data. The DIYD/jdrones props are not in there, but should give you good comparison datasets to work with. 
• Moderator

  Michael Pursifull November 7, 2011 at 8:10am

  From the jDrones Website 850Kv motor power out put from ESC, 3S LiPo, 10x45 Propeller 25% 50% 75% 100% Amp Wattage Thrust 1 A 11W 170gr 3.4 A 38W 433gr 9 A 100W 855gr 12.2 A 135W 1095gr

  880Kv motor power out put from ESC, 3S LiPo, 12x45 Propeller 25% 50% 75% 100% Amp Wattage Thrust 1.5 A 17.5W 230gr 6.1 A 70W 650gr 14.2 A 160W 1290gr 20A A 210W 1380gr
• 

  Jan van Hulzen November 7, 2011 at 8:06am

  Hi,

   

  is there information available on the lift characteristics of the arducopter propellers? I am looking for information to use in a theoretical calculation where i am able to relate lift to rpm.

   

  thank you for any information

   

  Jan
• Dara Shayda November 3, 2011 at 10:43am

  Sorry, I did not mean to name drop.

   

  For Canadians they can use these offices to get more info or apply for licenses:

   

  http://www.tc.gc.ca/eng/civilaviation/standards/general-recavi-regi... 

   

  We will do so since we like to fly for commercial activities.

   
• 

  Ellison Chan November 3, 2011 at 10:34am

  @Dara Shayda

   

  I'm sure Chris will have opinion, but since he's not a lawyer, he'll probably not want to give us a legal opinion.  The laws are simply not caught up with the technology yet, and if we all operate our Arducopters responsibly, there will be no need for any government to have to pass laws to limit our use of them.