Replies

  • ISM band are vary from different countries. 2.4GHz is common in all over the world. But the distance is not suitable for the UAV telemetry. In the Sub-Ghz band, 433MHz, 315MHz, 868MHz and 915MHz are all available between different countries. RF4432 can support the band from 150MHz to 950MHz.   It can support the local radio regulations. 

    • None of those radios seem to have specs any better than the 3DR/HopeRF radios, and they're closed source so good luck getting them to do anything fancy.

      The OP wanted something more powerful than 100mW.

      I suggest the RFD900...

      http://rfdesign.com.au/index.php/rfd900

      It transmits a nice, legal 1W 900mhz band signal.

      I highly suggest you don't hop up your already illegal 433mhz 3DR radio.

  • Hi

    I have used these:

    http://www.abacom-tech.com/500mW-RF-Power-Amplifier-PLA-05W-433AT-P...

    This amp reduces the receiving sensitivity, better to use higher gain antennas without these amplifiers, currently achieve approx. 5km with a 1/2 wave omni on ground and std antenna on airborne side.

  • The 433 3DR radio already puts out well more than the legal limit on that band.

    Probably not a good idea to put a heater on an already illegally operating device.

  • 433MHz long range is up to 5km. I don't know whether it satisfy with your requirement. 

    http://www.appconwireless.com/NEWS/shownews.php?lang=en&id=13

  • Bidirectional 433mhz are hard/impossible to find. I had a 900Mhz from Shireen...(https://www.shireeninc.com/osc/amplifiers-bidirectional/900mhz-bidi...)

    Don't waste your money. If you want real long range telemetry, it's with a dronecell on the cellular network. Check out "telemetry over IP" group, we are making progress....

This reply was deleted.

Activity

DIY Robocars via Twitter
Sep 9
DIY Robocars via Twitter
RT @chr1sa: We've got another virtual @DIYRobocars race tomorrow at 9:00am PT. Two dozen autonomous cars will compete, four at a time. Ther…
Sep 4
DIY Robocars via Twitter
Sep 1
DIY Robocars via Twitter
Aug 31
DIY Robocars via Twitter
Aug 31
sam liked Jimmy Oliver's profile
Aug 25
DIY Robocars via Twitter
RT @ExplorerRobocar: Sometimes, I am really a big kid!! Having fun with my virtual RC car on the @diyrobocars track 😜😉, by using the « AR R…
Aug 24
DIY Robocars via Twitter
RT @grepLeigh: @donkey_car @unity3d @TensorFlow ~1050 episodes into training, my agent learned to erratically drive in the left lane. 🤖😆 ht…
Aug 24
DIY Robocars via Twitter
RT @EclipseCyclone: Sweet! http://Robotec.ai high performance #ROS 2 @unity3d #CycloneDDS bridge for @AutowareFdn @SVLSimulator now…
Aug 24
DIY Robocars via Twitter
RT @a1k0n: My car had a lot of trouble getting around the track at the last @diyrobocars event -- only one actual finished lap during the r…
Aug 24
DIY Robocars via Twitter
RT @SmallpixelCar: This is the run time map https://t.co/VzykOkUt2G
Aug 24
DIY Robocars via Twitter
RT @SmallpixelCar: Made a lot progress on Warm Spring Raceways track. Almost finished one lap. https://t.co/nUVpufZQyP
Aug 24
DIY Robocars via Twitter
RT @AntonioRobotics: Super fun time seeing these autonomous cars race at @circuitlaunch for the @diyrobocars quarterly meet up! The demolit…
Aug 15
DIY Robocars via Twitter
RT @a1k0n: I thought my dumb localization code was still working at the new @circuitlaunch track, but it was just *barely* working. I shoul…
Aug 14
DIY Robocars via Twitter
RT @DAVGtech: Recording of entire in person @diyrobocars race today @circuitlaunch. Fast forward a couple hours to go straight to the racin…
Aug 14
DIY Robocars via Twitter
RT @SmallpixelCar: This is the run time map. Very noisy Lidar signal https://t.co/bAbeVUMi10
Aug 14
More…