Gender
Male
About
Please tell us a bit about your UAV interest
HW and SW development FPV flight
Hometown:
Pilsen
Activity Feed
"it looks that "D" param is removed from params. Or you can see it ?"
"I am aware of this but how it can happen during flight ? Declination is fixed, Auto Dec is disabled"
Can somebody help me with following problem ?Today was relatively bad wind and I flew in loiter/stab with my Y6B and everything was ok. But during second flight copter start do circles in loiter. You can see them as perfect sinuses on end of chart.…
"Try to connect full power also. For me it looks that USB power source is not strong enough to drive all connected stuff and thus generate this errors."
"Because there is/was lot of new ones without blobs joints on PCB. Yes, best is V2 with switching and blobs but in time of original post was problem to find them and some versions had switching but not easy way to interconnect. "
"Well, thanks for letting us know. I really expected that it will be something with power because it went away when I take off bluetooth module from copter. I can imagine that this will simply change way how is voltage getting off.
Can you give us…"
Can you give us…"
"Ok, so freezer bag was not cold enough to cool hawk down or problem is something different."
"So I put freezer bags on hawk and waiting.
Do somebody know what press_temp value means ? C divided by 100 ?
I just disabled GPS precheck (in basement doesn't work even Neo8) and now getting Thr below falsafe so I suppose that arming precheck are…"
Do somebody know what press_temp value means ? C divided by 100 ?
I just disabled GPS precheck (in basement doesn't work even Neo8) and now getting Thr below falsafe so I suppose that arming precheck are…"
"Craig, how can I see that it is LSM303D failure - because Acc on IMU2 is arround 60 which is out of scale ?"
"I definitely agree. It is good think that FW is improved and reporting more potential problematic during start-up. Security first, no question, better than see fly away or crash.
But I am trying to get on core - what is real problem. Lot of…"
But I am trying to get on core - what is real problem. Lot of…"
"I have couple of questions for HW issue arround "Bad ACC health"
- is known what is bad with boards ? Soldering, chip, board design, power problems or something is out of tolerance ?
- is there way how to easily and 100% detect that my board is…"
- is known what is bad with boards ? Soldering, chip, board design, power problems or something is out of tolerance ?
- is there way how to easily and 100% detect that my board is…"
"From my perspective - please, please, do nothing. Keep with army stuff and keep away from end customer market. We have enough "nice" video captures from Phantoms on YT and all of them went to more and more regulations.
Doesn't matter if you live in…"
Doesn't matter if you live in…"
"Fast temperature changes is something what sensors don't like - for example baro can show you big alt changes (even with correct code for temp compensation). This is reason why I am trying to power board and then let it for a while to heat itself to…"
"I found very similar problem - problem with Accel health in low temp (1-5 degree celsius). I didn't downloaded logs (not sure if I have there all prearm logs) yet but I have one idea
Is it possible that bluetooth module attached to Serial1 makes…"
Is it possible that bluetooth module attached to Serial1 makes…"
"I am using $9 bluetooth module connected to one copter. Sure, range is limited but still, 5m without cables is much better for configuration than cable :-)
And for Pixhawk - you need only cheap module from china and cable with DF13 to connect it…"
And for Pixhawk - you need only cheap module from china and cable with DF13 to connect it…"
"Yes, it will work as long as you keep same voltage level on both sides (which is problem on versions with different voltage regulator on analog side)"
