About

Gender

Male


Location

Tucson, AZ


Activity Feed

Antonio Watkins replied to Antonio Watkins's discussion Maps does not load in google maps in config tool
"No error message at all. The google map will not show up at all."
Oct 24, 2010
Antonio Watkins posted a discussion
Not sure if this is the correct place to post this but I can not get the map to load in the cinfig tool.  I am running microsft windows explorer.  Anybody have any ideas so I can fix this problem?
Oct 20, 2010
Antonio Watkins replied to mark's discussion I've never flawn an RC plane before. What simulator should I get to start out?
"Great planes Real flight. That is the only one that comes to mind right now but there are others."
Dec 6, 2009
Antonio Watkins posted a discussion
Does anybody know of a in expensive note book computer to program the Ardu pilot in the field?.
Nov 30, 2009
Antonio Watkins posted a discussion
Does anybody know if the shield board V2 comes with the male and female pins. I do not need all the hardware that comes with the V2 shield kit.
Nov 26, 2009
Antonio Watkins replied to Antonio Watkins's discussion problems with down loading code
"Could there be a problem with the top board?"
Nov 26, 2009
Antonio Watkins replied to Antonio Watkins's discussion problems with down loading code
"Thanks Chris for the last message. I followed it to the T. It worked. The code is loaded and Gps lock with the top board on bottom board. When using the Config tool with the top board on the ardu pilot, It will not write or read with or without the…"
Nov 26, 2009
Antonio Watkins replied to Antonio Watkins's discussion problems with down loading code
"Here is what I am doing

Downloaded Arduine 0017 and ardu pilot v2.4. Moved both files to desk top. Opened Ardu pilot folder 3 folders are there 1. ardu pilot easystar v24 2. ground station beta 3. ardupilot. There is no header file. The instruction…"
Nov 25, 2009
Antonio Watkins replied to Antonio Watkins's discussion problems with down loading code
"The arduine 0017 does not give me a compile message. It just says uploading then a few seconds later I get a error code."
Nov 25, 2009
Antonio Watkins replied to Antonio Watkins's discussion problems with down loading code
"All I see is the proccessing source code. I open up Ardu2.4, 3 folders are there one says ardu pilot, ground station beta 2
and ardu pilot v24. If I open up ardu pilot v24 that is were I see the processing source code. If I open the Ardu pilot…"
Nov 25, 2009
Antonio Watkins replied to Antonio Watkins's discussion problems with down loading code
"I am not seeing any .pde files. only proccessing source code files are they the pde files?."
Nov 25, 2009
Antonio Watkins replied to Antonio Watkins's discussion problems with down loading code
"Now it says

error:'data_update_event'was not declared in this scope

if((data_update_events&0x01)==0x01

in function' void navigation()':
error:'data_update_events' was not declared in this scope in function'void stabilization"
Nov 24, 2009
Antonio Watkins posted a discussion
Everytime I try to load the 2.4 code into the ardu pilot, I keep getting55 erorr:easystar.h:no such file or directoryany solutions?
Nov 24, 2009
Antonio Watkins replied to Antonio Watkins's discussion com port
"I am running windows XP. I went to the down load the FTDI drivers but what do I down load from the page? and where is it on the page?."
Nov 22, 2009
Antonio Watkins replied to Antonio Watkins's discussion com port
"I am using the ardu hardware, software, cabel, ubox GPS and the instruction manual. In using ardruino I open up the tools and the com port says it should be 5 or higher. I am trying to load the software to the board."
Nov 21, 2009
Antonio Watkins replied to Antonio Watkins's discussion com port
"yes I see systems and open it, then hardware and there is no com port in the list."
Nov 21, 2009
More…