About

Gender

Male


Location

Hibbing, MN


Please tell us a bit about your UAV interest

Quadcopters, tilt rotors, anything RC


Hometown:

HIBBING, MN


Activity Feed

Dan posted a discussion
Well im back for more help from you experienced folks out there, pretty sure i fried my board wen i fried my osd, tried setting up my fpv with the osd, powered it off my jst connection on my pdb, i removed the osd and the fpv seemed to work but…
Sep 15, 2016
Dan replied to Dan's discussion dumped MIssion Planner for APMplanner2
"Im inexperienced but i think as long as tge receiver can cable up to the 2.6 there should be no issue there, i calibrated my esc's manually one by one, watched lotsa youtube and showed me step by step my throttle issue has been solved, i reset the…"
Sep 13, 2016
Dan replied to Dan's discussion dumped MIssion Planner for APMplanner2
"I was so stoked i forgot to explain the fix, basically i reset the board and uploaded "ardurover" then reset the board again and uploaded ardurover again, i was told to do this a couple times, then reset and upload the proper firmware, admittedly it…"
Sep 10, 2016
Dan replied to Dan's discussion dumped MIssion Planner for APMplanner2
"Many thanks to all for the advice, i found a member with same throttle issue and a suggested fix, it worked!, have already crashed (due to showing off) and wrecked my gps module, but no worries, another on way, thought i was grounded but found out i…"
Sep 10, 2016
Dan replied to Taylor Mantick's discussion No Throttle Control
"Thank you so much! I don't know how you figured that process out, I had to repeat it more than a couple times but I was able to finally fly, I just ran it in stabilize for about 20 seconds a couple of times, everything banked correctly, pitched…"
Sep 8, 2016
Dan replied to Taylor Mantick's discussion No Throttle Control
"Same problem, did you ever get this issue  worked out??"
Sep 8, 2016
Dan replied to Dan's discussion dumped MIssion Planner for APMplanner2
"Another update, the set up in mission planner went different, firmware uploaded same, set up of mandatory hardware acted different, seemed to go smoother at first, then during compass calibration mavlink kept disconnecting and the same comport was…"
Sep 7, 2016
Dan replied to Dan's discussion dumped MIssion Planner for APMplanner2
"Update, i opened my apm 2.8 (version 2.8.8 as the board reads) after watching a couple videos about cutting a trace between two pads, having some electronics assembly experience i felt confident that i could at least visually inspect the board,…"
Sep 7, 2016
Dan replied to Dan's discussion dumped MIssion Planner for APMplanner2
"Ok, did i forget to mention that the red light on my external compass blinks all the time, i guess its supposed to be solid, now im learning on the 2.8 there is a jumper trace that needs to be cut, can anyone tell me if they have done this…"
Sep 7, 2016
Dan replied to Dan's discussion dumped MIssion Planner for APMplanner2
"Update, I recalibrated ESC's, I'm using a 4s Lipo, should hear 4 beeps and a long beep, signifying the 4s battery and successful calibration, Right? well I only hear 2 beeps and the long one, same throttle reaction, idles and the slightest throttle…"
Sep 5, 2016
Dan replied to Dan's discussion dumped MIssion Planner for APMplanner2
"Here's some pics of what I got going ondiy5.jpgdiy4.jpgdiy3.jpg"
Sep 5, 2016
Dan replied to Dan's discussion dumped MIssion Planner for APMplanner2
"Andre K. said:
No. ESC calibration is independent of the GCS software, in fact, you don't even need GCS software to do it.
But your problem sure sounds like ESC calibration related (not to be confused with RC calibration)
I hate to bring it to you,…"
Sep 5, 2016
Dan replied to Dan's discussion dumped MIssion Planner for APMplanner2
"Ive done it manually, one at a time, heard all the signifying beeps, do i need to do it again with the APMplanner2 that im using now?"
Sep 5, 2016
Dan posted a discussion
I removed Mission Planner from my computer, I was getting several pre arm check errors with mym2.8, I installed APMplanner 2, seemed super easy to go thru the set up, it was basically the same as Mission Planner, no errors, able to arm the motors,…
Sep 5, 2016