About

Gender

Male


Location

West Palm Beach, FL


About Me:

Just getting into AVP.


Please tell us a bit about your UAV interest

Focus on Aerial photo and video


Hometown:

West Palm Beach


Activity Feed

Jeremiah Walker commented on Hugues's blog post How-to guide: Pixhawk with 6S batteries (> 4S)
"So I'm following case 1 with the BEC on 180AMP Attopilot. I did not put the ground loop in between wire 5 and the BEC. Could this be the cause of extra heat produced? My tiger ESC do not have a bec. Reason for adding BEC."
Jan 11, 2015
Jeremiah Walker commented on Hugues's blog post How-to guide: Pixhawk with 6S batteries (> 4S)
"I am proud to purchase American products whenever possible in this economic drought we our in.

I agree entirely! They have teams of MIT kind of sort but yet can't produce a nice reliable module for aircraft that carry more than a mobious for more…"
Jan 2, 2015
Jeremiah Walker replied to Felix Meissner's discussion Problem connecting Pixhawk and Futaba receiver
"Hey Mike,

Still going well with 14SG?

Are you still on the same firmware?

Thank you."
Sep 7, 2014
Jeremiah Walker commented on Hugues's blog post How-to guide: Pixhawk with 6S batteries (> 4S)
"Ronnie,
Please understand I am wanting to make sure that neither of us especially me not giving false info and back up with facts. Thats all I want from this discussion Ronnie. I am and should be considered your friend here. I don't want my $17,000…"
Aug 30, 2014
Jeremiah Walker commented on Hugues's blog post How-to guide: Pixhawk with 6S batteries (> 4S)
"Good morning Ronnie,
I am enjoying this and please tell me why you think that the spec sheet for the 180amp Attoopilot is inaccurate from the manufacture? They claim good to 360amps."
Aug 30, 2014
Jeremiah Walker commented on Hugues's blog post How-to guide: Pixhawk with 6S batteries (> 4S)
"Thank you for engaging in this discusion with me. This is where I like to solve my problems before putting all that money in the air and helping not contribute to bad media about our hobby. I am on the fence as well.

After submitting the spec sheet…"
Aug 30, 2014
Jeremiah Walker commented on Hugues's blog post How-to guide: Pixhawk with 6S batteries (> 4S)
"I felt the same way. Then my friend the chief aeronautical engineer at Grumahn " Friend of mine" did some math with me and read the spec sheet. No problem. I have the math and spec sheet proving. Its no different than pulling 180amps with the 90amp…"
Aug 30, 2014
Jeremiah Walker replied to Felix Meissner's discussion Problem connecting Pixhawk and Futaba receiver
"How many channels on pixhawk are you running?"
Aug 29, 2014
Jeremiah Walker replied to Felix Meissner's discussion Problem connecting Pixhawk and Futaba receiver
"What airframe is this in?

How many channels? I assume 8 because that is it on PPM encoder. But you say Sbus is solved then I think you are succesfully using Sbus.

Are your Tx settings something you could share with me?

Thank you for all of your…"
Aug 3, 2014
Jeremiah Walker commented on Hugues's blog post How-to guide: Pixhawk with 6S batteries (> 4S)
"Thank you much Aaron and Hugues."
Jul 30, 2014
Jeremiah Walker commented on Hugues's blog post How-to guide: Pixhawk with 6S batteries (> 4S)
"That is what I would like to accomplish here in this site. I am a safe/responsible pilot but I am not a low voltage tech. I am completely lost as how to accomplish my goal. I am a photographer and desperately need to get this up and running. I have…"
Jul 30, 2014
Jeremiah Walker commented on Hugues's blog post How-to guide: Pixhawk with 6S batteries (> 4S)
"Hello Hugues,
   I am building a hex with Tiger motor U7 swinging 18" props. My math says I will be drawing roughly 250amps max cont. It is a very beefy motor. Down the line I would like to run 8s to lift Red Epic camera and lens."
Jul 29, 2014
Jeremiah Walker commented on Hugues's blog post How-to guide: Pixhawk with 6S batteries (> 4S)
"Thank you. I ran across something at Honeywell. Dont have time at moment to dig thru history at the moment but they did have a product that did both on that voltage and wattage. More or less anything you can imagine. But if only we can make it work…"
Jul 21, 2014
Jeremiah Walker commented on Hugues's blog post How-to guide: Pixhawk with 6S batteries (> 4S)
"Ahmed,
The 180 amps is a calculated max continues. I plan on running three different camera gimbal combos. The Tarot 960 is a big enough platform it will carry a very big camera on a light gimbal. Just needs power. That I have with the U7 Tiger…"
Jul 21, 2014
Jeremiah Walker commented on Hugues's blog post How-to guide: Pixhawk with 6S batteries (> 4S)
"I am also considering 8s for a heavy lifter. Would like to do the same with that as well."
Jul 18, 2014
Jeremiah Walker commented on Hugues's blog post How-to guide: Pixhawk with 6S batteries (> 4S)
"I will someday need to swing a bigger prop so I would like to stay on exactly how the best way to draw over 180amps safely and reliably is. So please anyone chime in on this."
Jul 18, 2014
More…