Gender
Male
About
Location
Salt Lake City, UT
About Me:
New to the RC UAV, However very quick learner and hope to contribute back to community.
Please tell us a bit about your UAV interest
Building UAV based on open-source tech.
Hometown:
Salt Lake City
Activity Feed
"Link to video demo of flights and advantages.
https://www.youtube.com/watch?v=sbuGCgc-JCM
http://www.fastcompany.com/1646372/uav-samari-lockheed-martin-helic..."
https://www.youtube.com/watch?v=sbuGCgc-JCM
http://www.fastcompany.com/1646372/uav-samari-lockheed-martin-helic..."
"Can you share how you are powering up the APM and connecting the USB. I have read that hooking them both up at the same time can short out the APM. Do you use a BEC and isolate the power from the APM and ESC."
"Double check the transmitting rates."
"Jani,
Thanks for the reply. I'm just a little overly enthusiastic with the project and the community. I love this stuff. I will hold tight until the official release. I might have to buy a second board so I bug the ArduPilot Megas guys also ;)…"
Thanks for the reply. I'm just a little overly enthusiastic with the project and the community. I love this stuff. I will hold tight until the official release. I might have to buy a second board so I bug the ArduPilot Megas guys also ;)…"
"Update,
Modified the cable going from the APM to the GPS adapter only discontenting the tx. Everything stabilized. I'm thinking I got my GPS in a unsupported or mode refresh rate ect... or the alpha software dose not understand the stream and is…"
Modified the cable going from the APM to the GPS adapter only discontenting the tx. Everything stabilized. I'm thinking I got my GPS in a unsupported or mode refresh rate ect... or the alpha software dose not understand the stream and is…"
"Ken,
Thank you for the reply, I will start tracking down that direction."
Thank you for the reply, I will start tracking down that direction."
Has anybody seen this behavior before. When the MediaTek MT3329 is hooked up I see some sort of noise in the read outs. Several of the indicator jump at a specific intervals. I’m able to run both the NMEA and MTK Binary test code ok and reports…
"Here is the code I pasted into the ArduinoPilotMega and uploaded. After successful MTK update you will see what looks like garbage in the serial monitor. This is the binary output. One you see it you can upload GPS_MTK_test.pde found in the latest…"
"I have confirmed the MTK is in NMEA mode. Is there a beginner guide to reset it to binary mode?
I have reviewed the link in the store and understand I need to send the GPS a string to reprogram it.
$PGCMD,16,0,0,0,0,0*6A = Binary mode
How is it…"
I have reviewed the link in the store and understand I need to send the GPS a string to reprogram it.
$PGCMD,16,0,0,0,0,0*6A = Binary mode
How is it…"
I'm having an issue establishing data from theMediaTek MT3329. Its connected to the APM (Red board) using the ublox cable from the diydrone store. The MTK adapter board has a solid blue light (Lock). I have reseated the ublox cable a couple of…
"Jason,
Thank you this resolved my issue.
Cheers"
Thank you this resolved my issue.
Cheers"
"Javier,
Thank you, just know it can be done helps, I will keep at it and reset my source files and try again."
Thank you, just know it can be done helps, I will keep at it and reset my source files and try again."
"WiFi Servo Controller with webserver.
http://www.endurance-rc.com/controllers.html"
http://www.endurance-rc.com/controllers.html"
