About

Gender

Male


Location

Quebec


About Me:

custom quad


Please tell us a bit about your UAV interest

custom quad


Hometown:

Mirabel


Activity Feed

Martin Ouellette replied to Martin Ouellette's discussion Signal loss while auto mission
"Yes, but a "long time ago"...
I don't remember why, but when I configured my FS i choosed the way by using the FS of the rx/tx rather than the firmware way.

I will read again about that."
Oct 14, 2014
Martin Ouellette posted a discussion
Hi,I'm flying often using auto mission.I'm currently on arducopter 3.2 RC10.Yesterday, while a mission, I reached the limit of my frsky signal.I wonder what will happen if I loose my signal while the mission ?I configured a failsafe directly on my…
Oct 14, 2014
Martin Ouellette replied to Randy's discussion ArduCopter-3.2 beta testing
"Well, I found the parameter ...
in switches.pde file.
just change int16_t pulsewidth = g.rc_5.radio_in; for int16_t pulsewidth = g.rc_6.radio_in;"
Oct 5, 2014
Martin Ouellette replied to Randy's discussion ArduCopter-3.2 beta testing
"Hi,

I'm running rc10 on my APM 2.5.
I switched my RX (FrSky) to use CPPM mode yesterday. Now i'm trying to configure my flight mode. I was using 6 flight by mixing my 3-pos switch and gear switch (turnigy 9x remote).
Now my 3-pos switch respond on…"
Oct 5, 2014
Martin Ouellette replied to Randy's discussion ArduCopter-3.2 beta testing
"Hi,

I don't know if it's correct that I reply in this thread with my question but as it's one of the most active thread then I do.
Well, I fly using version 3.1.5 since a lot of time and I would like to upgrade to 3.2 version specially to try the…"
Sep 9, 2014
Martin Ouellette replied to Patrick Helsemans's discussion Failsafe apm 2.5 with frsky and turnigy 9x
"Just to "close" my discussion, I got the courage to try the failsafe again with a good setup on all channels...worked great !!

thanks again Detlef for ur time."
Aug 4, 2014
Martin Ouellette replied to Patrick Helsemans's discussion Failsafe apm 2.5 with frsky and turnigy 9x
"DetLef,
After read your reply, and also read again the FrSky instruction about setting up the failsafe...I found that I did something very wrong.
As you wrote, when the FrSky learn button is pressed it saved the value of all channels...and I'm sure…"
Aug 1, 2014
Martin Ouellette replied to Patrick Helsemans's discussion Failsafe apm 2.5 with frsky and turnigy 9x
"Detlef, thanks for your fast answer :)
"You can choose to use the RX failsafe alone but then you must teach all important channels like flight mode, throttle, and sticks a certain value to keep your copter flying"
If I correctly understand, I need…"
Aug 1, 2014
Martin Ouellette replied to Patrick Helsemans's discussion Failsafe apm 2.5 with frsky and turnigy 9x
"Umm no answer since 2 months, I hope this post is still alive.
I got the same problem than BertzillAvionics.
I configured failsafe on my FrSKY to call a RTL. I didn't configure anything about FailSafe into the APM.
I tested in MP, when I turn off…"
Aug 1, 2014
Martin Ouellette left a comment for Jim Wittstruck
"Hi Jim,

I'm writing directly to you because I read one of your post that didn't get a lot of answer.

http://diydrones.com/m/group/discussion?id=705844%3ATopic%3A1650476

Did you be able to find your problem ?

I have some problem with my quad…"
Jun 11, 2014
Martin Ouellette replied to Martin Ouellette's discussion APM 2.5 peak vibration
"Leonardo, nop, did not balanced the props. Probably my bad but I thought that because they are made in carbon I do not have to do this ?!
I'll take a look of that.
Is it possible that I have behavior like that by "only" having unbalanced props ?…"
May 20, 2014
Martin Ouellette posted a discussion
Hi guys,I need help to find out my problem.I have a quad on a sk450 frame with apm 2.5, FkSry tx/rx, AfroESC 30a, 28-30s 900kv motors and neo-ublox gps.I crash my quad last week. Apart the four propellers and some nylon spacers and screw,…
May 20, 2014