About

Gender

Male


About Me:

Oselladore


Please tell us a bit about your UAV interest

I am interested in developing new UAV technologies.


Hometown:

Chioggia


Activity Feed

Mattia commented on Patrick Duffy's blog post How to setup a Mission Planner HD-Video HUD using GStreamer and Mission Planner plugins
"@Patrick, I had to uninstall, delete the folders and reinstall both programs, but now I don't have the error anymore. In the next days I will try to stream, but I believe there will not be problems. Thanks!
Can you explain me what is the "Cam…"
Jan 6, 2017
Mattia commented on Patrick Duffy's blog post How to setup a Mission Planner HD-Video HUD using GStreamer and Mission Planner plugins
"@Patrick, thanks. I have installed the stand-alone plugin but when I execute the program, I got this error:

The program anyway starts, but when I start the streaming from my RPI, the HUD immediately crashes...
Any idea?"
Jan 6, 2017
Mattia commented on Patrick Duffy's blog post How to setup a Mission Planner HD-Video HUD using GStreamer and Mission Planner plugins
"Hi, I had the same problem than Tommy_768 (Gstreamer HUD disappear from the options) after updating my MissionPlanner. I tried all the previous versions and the last that works fine is the 1.39.
Robert Mapes suggests to use the stand alone version…"
Jan 5, 2017
Mattia replied to Mattia's discussion Battery voltage failsafe
"The "strange" thing is that in my case the voltage drops below 14V only if the current consumption is really high for some demanding maneuvers, but as soon as I go back to cruise speed, the current consumption goes to 20A and the voltage goes back…"
Aug 11, 2016
Mattia posted a discussion
Dear all,I am using a Tiger battery 4S 6000mAh 35C and I set the voltage failsafe in Mission Planner at 14.0V (3.5V per cell as suggested).The problem is that from 50% of the discharge of the battery (3000mAh used), if the current request increases…
Aug 10, 2016
Mattia posted a discussion
Dear all,I don't find information about the "Change Speed" button is in the "Actions" tab in Mission planner. Is it the speed in m/s? Is it working correctly?I did a test pressing it while flying with may multicopter to a waypoint with it set at…
May 29, 2016
Mattia posted a discussion
Dear all,I am setting a joystick to flight with the MissionPlanner and I saw there are a lot of available options for every button that can be selected from the dropdown menu. This is the complete…
Feb 1, 2016
Mattia posted a discussion in PIXHAWK
Dear all,I have a hexacopter with a Pixhawk flight controller. I have decided to use an old Hitec 35Hz radio I had to control it with a PPM encoder and it does hits job, the problem is that it is too much disturbed by interference and I have risked…
Jan 30, 2016
Mattia posted a discussion
Dear all,I am setting up a drone with FPV via 3G USB modem connected to a Raspberry. The problem is that this modem is creating a lot of interference to my RC receiver, so it becomes quite hard to control the drone. The receiver is a quite old Hitec…
Jan 7, 2016
Mattia posted a discussion
Hi everybody,I have bought the DJI E300 kit and the ESC comes with a coaxial cable for the power. In the kit there is already a distribution board, but the power cable are soldered, so it is not comfortable in case I want to remove something. I…
Dec 2, 2015
Mattia posted a discussion
Dear all,I would like to build my first drone and I need some advice to chose the motors.My idea is to build an hexacopter with an empty weight of 2kg and a payload of 3kg, so I am looking for 6 motors with the right trust. I have seen the DJI E600…
Mar 22, 2015