Please tell us a bit about your UAV interest
Quadcopter hobbyist and aerial videomaker
About
Hometown:
Warszawa
Activity Feed
"Hi,
I was looking for the explanation of altitude loss when moving copter horizontally forward (and other directions) - but I never found a simplest explanation. When the craft is moving forward it is leaning towards the front (pitch) i.e. at…"
I was looking for the explanation of altitude loss when moving copter horizontally forward (and other directions) - but I never found a simplest explanation. When the craft is moving forward it is leaning towards the front (pitch) i.e. at…"
"Hi Jean-Marie
IT WORKS! Thanks for your help and suport. Actually, I dont know what happened, I think crucial
was setting serial 2 baud (where playosd was finally connetced) and board serial rate (both to 38 400)
Thanks a lot! Where should I send a…"
IT WORKS! Thanks for your help and suport. Actually, I dont know what happened, I think crucial
was setting serial 2 baud (where playosd was finally connetced) and board serial rate (both to 38 400)
Thanks a lot! Where should I send a…"
"Hi,
1/ reversing rx and tx didn't help
2/ serial speed in both playuav and mission planer set at 57600 baud
any ideas?"
1/ reversing rx and tx didn't help
2/ serial speed in both playuav and mission planer set at 57600 baud
any ideas?"
"Hi,
I now have osd display and video from camera! Problem was probably in bad connection.
But now I have osd display, but no data from Pixhawk - I checked all connections again, everything seems
to be ok, but no data displayed. I tried Telemetry…"
I now have osd display and video from camera! Problem was probably in bad connection.
But now I have osd display, but no data from Pixhawk - I checked all connections again, everything seems
to be ok, but no data displayed. I tried Telemetry…"
"I've checked with your video - no blue light visible on it.
I hope the author/producer of PlayUAV OSD will improve the documentation by adding 2-3 sentences concerning the connections and meaning of the LEDs "
I hope the author/producer of PlayUAV OSD will improve the documentation by adding 2-3 sentences concerning the connections and meaning of the LEDs "
"Hi Jean-Marie,
I have video in/out connections ok. But I do not have blue light - I assumed the board is powered by Pixhawk through the supplied cable - the red wire is connected to +5V, right? But I never saw the blue light.
Question: when…"
I have video in/out connections ok. But I do not have blue light - I assumed the board is powered by Pixhawk through the supplied cable - the red wire is connected to +5V, right? But I never saw the blue light.
Question: when…"
"Hi,
I dont have another VTX (video transmitter I guess) but I tested also directly with the screen - same result - no signal. My board is new - received from Banggood 2 days ago, has AT7456 chip, board version 2015-11-25 Ver 1."
I dont have another VTX (video transmitter I guess) but I tested also directly with the screen - same result - no signal. My board is new - received from Banggood 2 days ago, has AT7456 chip, board version 2015-11-25 Ver 1."
"Hi Jean_Marie,
thanks - but shouldn't the board produce the video output without camera input? I didn't try Video 2 In but
I expected to see the video output anyway - it should display all defined in Config tool screens, am I right?"
thanks - but shouldn't the board produce the video output without camera input? I didn't try Video 2 In but
I expected to see the video output anyway - it should display all defined in Config tool screens, am I right?"
"I can't get any video from my PlayUAV OSD - connected to Piixhawk Telemetry 1 socket, video in to camera, video out to ImmersionRC video transmitter, red LED is blinking rather slow - but no signs of video on receiver.
What else can I do to get it…"
What else can I do to get it…"
