About

Gender

Male


Location

Montreal, Quebec


Please tell us a bit about your UAV interest

STM32F4 based APs


Hometown:

Istanbul, Turkey


Activity Feed

OlivierD. commented on Steven's blog post Worlds smallest autopilot (yet)
"Awesome. That is micro beauty."
Aug 26, 2013
OlivierD. commented on Kirill's blog post SmartAP is fully autonomous autopilot
"Very nice Kirill, STM32 is the way to go. How much does your board retail for?"
Jul 20, 2013
OlivierD. commented on OlivierD.'s blog post Future HUD - Ground Station Shades?
"Lol! We're there. Next up is a replicator so we can make a quick cheese-burger at the field."
Jul 8, 2013
OlivierD. commented on OlivierD.'s blog post Future HUD - Ground Station Shades?
"One way it could be interesting is if the right hand mini screen displayed what the gimbal is seing, it would be interesting for aerial shooting. And overlay some basic info like battery state, altitude, heading etc.... For the life of me, I could…"
Jul 8, 2013
OlivierD. commented on OlivierD.'s blog post Future HUD - Ground Station Shades?
"And film your quad by looking at it, which would be natural while flying LOS. Not sure what the video quality would be like, says HD but not much info."
Jul 8, 2013
OlivierD. posted a blog post
Recon JetCould be fun, you could fly LOS and still have important info displayed right on your shades. 
Jul 8, 2013
OlivierD. commented on frederic reblewski's blog post 3D printed brushless gimbal for GoPro
"Great flyiing Julien, I personally could not do FPV through the gimbal, my internal gyros would be all confused! And the gimbal looks like it works very well. Good job. I will post a video of mine when I am finished."
Jul 3, 2013
OlivierD. commented on frederic reblewski's blog post 3D printed brushless gimbal for GoPro
"@Julien Watier: From a balance standpoint, the GoPro has most of it`s weight on the left side of the lens (battery) so it makes more sense to put the pitch motor to the right of the lens. The pitching assembly will then have a natural tendency to…"
Jul 2, 2013
OlivierD. commented on frederic reblewski's blog post 3D printed brushless gimbal for GoPro
"@Ben Norris. Very keen observation, all the gimbal manufacturers make the same mistake, as a result, the gimbal rolls off the gopro`s lens center. The motor should be inside the cradle that holds the GoPro, to the right of it so it would naturaly…"
Jul 2, 2013
OlivierD. commented on AKRCGUY's blog post GoPro Hero 3 Update NOW Available!
"Like Time said, if it was software, they would have fixed it by now. The trouble is, if it is hardware, and the thousands of reports point in that direction, we have to wait until GoPro release a second HW edition of the 3 series. In doing so, they…"
Apr 7, 2013
OlivierD. commented on AKRCGUY's blog post GoPro Hero 3 Update NOW Available!
"The problem is a hardware issue. GoPro made a huge batch to be ready for the holidays, a huge percentage of those have a hardware defect.  Until that batch is gone from the shelves and GoPro starts selling a revised hardware version, the 3 series…"
Apr 6, 2013
OlivierD. commented on John Wiseman's blog post ADS-B decoding on an AR.Drone
"That is cool! Now all we need is transponders to broadcast our positions. "
Apr 2, 2013
OlivierD. replied to Chris Anderson's discussion Feedback on new manuals
"Chris, that is a step in the right direction. People need to have a resource they can tap into for setup that is up to date and matching whatever code they are using. You owe them that much. Reading through a 275 page thread to figure out how to fly…"
Apr 1, 2013
OlivierD. left a comment for OlivierD.
"Merci Maxime! I will pick one up and play with it, could potentialy work out to be a good bypass solution.
Regards,"
Mar 31, 2013
OlivierD. left a comment for Maxime Carrier
"Maxime, you seem to know your way around electronics so I am sure you will figure out a way to make it safe. I am interested in your RX switcher, where did you get it, do you have any information on it? Thanks!"
Mar 31, 2013
OlivierD. left a comment for Maxime Carrier
"Hi Maxime, to make it safe, you need to figure out a way to be able to completely bypass the APM if it gets wonky, and it will at times. Some sort of external failsafe, something like this:
http://www.millswoodeng.com.au/failsafe_device.html
It can…"
Mar 31, 2013
More…