Gender
Male
About
Location
Porto Alegre, RS
Please tell us a bit about your UAV interest
FPV, Aerial Footage
Activity Feed
.jpg?width=584&profile=RESIZE_584x)
"Sorry about you loss.
if is fresh water, you can use Isopropyl alcohol to clean. Chances are pretty good.
Btw mate, i have some markers on batteries that you can switch between green and red label. After using it, i never mixed out batteries…"
if is fresh water, you can use Isopropyl alcohol to clean. Chances are pretty good.
Btw mate, i have some markers on batteries that you can switch between green and red label. After using it, i never mixed out batteries…"
"Randy, two weeks ago I asked for help because I was having a message "bad compass health" using an external mag. Ended up I changed the external mag for another one, same type, and problem is gone. No more error messages. Maybe i just had bad luck…"
"Hello guys. I need some help.
I am using the latest fw rc7....
I have installed the ext mag too.
after flying 15minutes on compass learning. I`ve checked the offset numbers...
they are low as 40,42 and 6 on z axis.
Mag interference is oscilante from…"
I am using the latest fw rc7....
I have installed the ext mag too.
after flying 15minutes on compass learning. I`ve checked the offset numbers...
they are low as 40,42 and 6 on z axis.
Mag interference is oscilante from…"
"Randy. May you help me?
I installed the external compass. Now motor interference is down from 130% to 13% only. Loiter is not trying to flip the ufo anymore. Woot! But a new problem is born. After external compass z offset is over 400. Y and X are…"
I installed the external compass. Now motor interference is down from 130% to 13% only. Loiter is not trying to flip the ufo anymore. Woot! But a new problem is born. After external compass z offset is over 400. Y and X are…"
"Today I tested the new firmware in my Octa.
Its is flying pretty stable until i try the loiter
I have no idea why but each time i switch to loiter Octa banks almost 90 degree instantly, in pretty aggressive maneuver. I have 3 apm 2.5 here and this…"
Its is flying pretty stable until i try the loiter
I have no idea why but each time i switch to loiter Octa banks almost 90 degree instantly, in pretty aggressive maneuver. I have 3 apm 2.5 here and this…"
"Guys. I need some help. I really dont know what I am doing wrong. I am testing the new beta firmware and I am trying to use the compassmot command. Problem is when I enter in CLI the compassmot command, I receive the regular message about increase…"
"Wow. Just tried new 2.9 in altitude hold and was pretty damn good. Just covered the baro sensor with those woman cotton makeup remover (looks like cotton discs) and used 3M Micropore hypoallergenic paper tape to keep in place. Nice one developer…"
"Guys, I am setting up a hexa and I am still learning how to read graphs.
Vibes are ok?
Throttle trim is showing 551 value. It is underpowered? I fell it mushy and p rate it is already at 0,21 and its asking for more. I have to chase the hexa too…"
Vibes are ok?
Throttle trim is showing 551 value. It is underpowered? I fell it mushy and p rate it is already at 0,21 and its asking for more. I have to chase the hexa too…"
"Hello guys.
I am facing a problem and I cant solve. I have the v 2.5 board with the 3dr radio.
Uploaded the new 2.9 version, erase the eprom, and set all hexa again.
Then I start flying. Its working normally. Stock rate P is a little high. Then I…"
I am facing a problem and I cant solve. I have the v 2.5 board with the 3dr radio.
Uploaded the new 2.9 version, erase the eprom, and set all hexa again.
Then I start flying. Its working normally. Stock rate P is a little high. Then I…"
