About

Gender

Male


Location

Gaylord, MI


About Me:

me


Please tell us a bit about your UAV interest

Never wanted RC, always wanted a small aircraft.


Hometown:

Ishpeming


Activity Feed

Scooter replied to Daryl Wilding-McBride's discussion Using an RFD900 with Solo in 3DR SOLO
"Where can I get an accessory bay breakout board?  "
Apr 10, 2016
Scooter replied to Daryl Wilding-McBride's discussion Using an RFD900 with Solo in 3DR SOLO
"Please assist me with this process.  I have a RDF900 and this is one of the things that annoyed me with SOLO is the inability to use the long range telemetry. "
Apr 10, 2016
Scooter replied to Scooter's discussion Voltage on APM 2.6 with generic power module in ArduPlane User Group
"Well I thought maybe cutting the ground to the speed controller would work, right up to the point I cut it.  As the heard the wire snip it dawned on me that I had never checked the voltage with the speed controller connected.  So before testing the…"
Oct 29, 2015
Scooter replied to Scooter's discussion Voltage on APM 2.6 with generic power module in ArduPlane User Group
"I run a BEC I'm it's not a high capacity, but I only run 4 small servo's off it (9 gram) So I figure that should be fine.  With the BEC I am still to cut the ground wire off the speed controller?  You description of what happened to you sure seems…"
Oct 28, 2015
Scooter replied to Scooter's discussion Voltage on APM 2.6 with generic power module in ArduPlane User Group
"just cut it? The speed controller wire? Where will the speed controller ground without a ground wire. Also to be clear. The BEC off the speed ground, or the speed signal ground wire?"
Oct 28, 2015
Scooter posted a discussion in ArduPlane User Group
I have a generic APM power module.  When I measure the power coming out of the module I find it to be 5.1-5.2V.  When I measure the voltage across A01 I find it to be 4.7-4.8V. When I look at th3e telemetry data it shows 4.7-4.8v, it varies a bit…
Oct 28, 2015
Scooter posted a discussion
I have a generic APM power module.  When I measure the power coming out of the module I find it to be 5.1-5.2V.  When I measure the voltage across A01 I find it to be 4.7-4.8V. When I look at th3e telemetry data it shows 4.7-4.8v, it varies a bit…
Oct 27, 2015
Scooter replied to Scooter's discussion Been working on this thing for a year need to share with somone. in ArduPlane User Group
"So I have tested the system live a few times.  I have a habit of running a live prop often to see if a modification will work out, only been bit once. 

I didn't notice a brown out.  As I think about when these flight start going downhill, it's when…"
Apr 1, 2015
Scooter replied to Scooter's discussion Been working on this thing for a year need to share with somone. in ArduPlane User Group
"That would be great.  I was able to fix up the plane and put it up tonight and splashed it again.  This aircraft with the foam booms was 100% dependable now it flies well for a while, then I have not idea what it is doing.  Last night the problems…"
Apr 1, 2015
Scooter replied to Scooter's discussion Been working on this thing for a year need to share with somone. in ArduPlane User Group
"Update.  To reduce weight so I could add another flight battery I removed the foam booms and used carbon fiber.  All was going well.  Little over 10 minuets in the air when the autopilot switched to manual, three seconds later this.  I am not sure…"
Mar 31, 2015
Scooter replied to Scooter's discussion Powering the RDF 900
"It draw 800ma at full power. The PM provides a max of 2.5A  not sure what the APM, GPS, and RC receiver draw. Seems like with 1/3 taken up by the RDF you could be pushing the limits.  If the PM overloads, you loose the APM, RC receiver, and…"
Mar 31, 2015
Scooter posted a discussion
I have an RDF 900 and have been powering the front side of the of my APM 2.5 from a dedicated battery.  I have decided to use this weight to increase flight time by adding a power module and for the board and a second battery.  From what I can tell…
Mar 31, 2015
Scooter replied to Scooter's discussion Been working on this thing for a year need to share with somone. in ArduPlane User Group
"AUW is around 3.1 pounds.  I think with a few modification I can get it down to 2.6 pounds.  Below I have given the power specs.  I am looking for a new motor prop combination that will provide better efficiency and maybe a few more watts power for…"
Mar 28, 2015
Scooter replied to Scooter's discussion Been working on this thing for a year need to share with somone. in ArduPlane User Group
"It has a 60" wingspan and a 48" length.  The power plant is a 2200KV 350W motor turning a 6X3.5 prop.  The booms limit prop size to 7".  I am considering changing the motor to something larger.  The batteries I am using  are 2 X 2200mah 20C and it…"
Mar 28, 2015
Scooter posted a discussion in ArduPlane User Group
     My son and I have been working on this UAV for  year.  We started by designing a foam model and then glide tested it, then started adding to it, servos, power plant, APM 2.5, GPS, rudder yaw damper system. It's been a work in progress.  The…
Mar 27, 2015
Scooter replied to Derin Hakan Karakurt's discussion APM Planner Autoland Setup Problem
"I'm no expert, but today I flew a 1.5 mile mission full auto, from takeoff to landing.  I never touched the RC.  For landing I set  waypoints to make a base and final leg.  I placed a waypoint on the obstacle at the end of the field I am using with…"
Mar 24, 2015
More…