Gender
Male
About
Please tell us a bit about your UAV interest
Hobby
Hometown:
France
Activity Feed
"Hi Bart, yes we want to deliver medicines in Madagascar before the end of the year here is my Email address: stephane@aerialmetric.com - skype: stephane.bihr
Regards"
Regards"
"Hi Rob,
In the next months we (my company and NGO's) should find the best way to transport medicines in Madagascar by drones. We have to cross more than 10km with more than 2kg payload, do you think that a converted hobby helicopter could be the…"
In the next months we (my company and NGO's) should find the best way to transport medicines in Madagascar by drones. We have to cross more than 10km with more than 2kg payload, do you think that a converted hobby helicopter could be the…"
"Do you think that the Pixhawk supply enought amps for RFD900 at 30dB on the telemetry port ?
Do I have to use a UBEC instead of the telemetry port supply ?"
Do I have to use a UBEC instead of the telemetry port supply ?"
"Hi Seppo,
I’ve just received the RFD900 warranty replacement and free antennas
Thank you very much
I have a 8kg octocopter and I try to get the best range possible with your RFD 900 Modem
On the octocopter, the two antennas are separated 40cm and I…"
I’ve just received the RFD900 warranty replacement and free antennas
Thank you very much
I have a 8kg octocopter and I try to get the best range possible with your RFD 900 Modem
On the octocopter, the two antennas are separated 40cm and I…"
"Thanks Manu
According to http://copter.ardupilot.com/wiki/parachute/ I thought that the only condition for manually deploy is CHUTE_ALT_MIN, and set it to zero is to disable CHUTE_ALT_MIN, so I shouldn't get the message "Too Low"."
According to http://copter.ardupilot.com/wiki/parachute/ I thought that the only condition for manually deploy is CHUTE_ALT_MIN, and set it to zero is to disable CHUTE_ALT_MIN, so I shouldn't get the message "Too Low"."
"Hi,
I'm trying to manually deploy a parachute with Ch8 to test it before takeoffCHUTE_ALT_MIN is set to zeroBut I get a message "Parachute: Too Low""
I'm trying to manually deploy a parachute with Ch8 to test it before takeoffCHUTE_ALT_MIN is set to zeroBut I get a message "Parachute: Too Low""
"Hi Ravi
I also have a problem with takeoff command you can see the issue here: http://ardupilot.com/forum/viewtopic.php?f=25&t=6311"
I also have a problem with takeoff command you can see the issue here: http://ardupilot.com/forum/viewtopic.php?f=25&t=6311"
"I think the main problem is that the altitude (50m) of the first command of the mission was not taken into account, the copter has not climbed 50m before the next command,
WHY ????
Instead an altitude of 25m at a speed of 90km / h hitting a tree…"
WHY ????
Instead an altitude of 25m at a speed of 90km / h hitting a tree…"
"Hi everyone,
Everything was perfect with my octa quad and pixhawk and arducopter 3.1.2 since this big crash in auto mode
Few seconds after takeoff, the pitch increased to 45° and speed 25 m/s ! but loiter speed and nav speed were set at 12m/s
I've…"
Everything was perfect with my octa quad and pixhawk and arducopter 3.1.2 since this big crash in auto mode
Few seconds after takeoff, the pitch increased to 45° and speed 25 m/s ! but loiter speed and nav speed were set at 12m/s
I've…"
"I've just ordered two of these http://www.marsparachutes.com/mars-mini/
Is there a way to use a script in Mission Planner to monitor the drone in flight and if a fall is detected it will deploy the parachute (servo ?) , for exemple an acceleration…"
Is there a way to use a script in Mission Planner to monitor the drone in flight and if a fall is detected it will deploy the parachute (servo ?) , for exemple an acceleration…"
"so I'll order a new board ! What's the good way to power the board (with Lipo and USB in the same time) to avoid this kind of problem ? I have an Attopilot 180A sensor and 3A 5.3V ubec plugged in one of the outputs with the JP1 plugged Can I plug…"
