About

Gender

Male


Location

bradford


About Me:

Beginner


Please tell us a bit about your UAV interest

Been building for a few months learning something new everyday


Hometown:

bradford


Activity Feed

saqib shafiq replied to Randy's discussion ArduCopter-3.2 beta testing
"Guys would it be worth switching back to 3.1 untill this has become more stable. The only reason for switching was due to the rssi volt parameter. Will i need to re-do all my settings if i switch back. Seems like there's alot of issues on this beta…"
Sep 21, 2014
saqib shafiq replied to Randy's discussion ArduCopter-3.2 beta testing
"Yes i meant althold and loiter mode. Has anyone tried to see if it affects the landing? Iv not quite got my hex ready to fly and i do not want to risk any damage to it. I was playing about with it and when the sonar goes below 20cm i get a varied…"
Sep 20, 2014
saqib shafiq replied to Randy's discussion ArduCopter-3.2 beta testing
"Wont that cause any problems when landing in auto. And thanks for reply"
Sep 20, 2014
saqib shafiq replied to Randy's discussion ArduCopter-3.2 beta testing
"Pic 1 sonar reading when in land position
Pic 2 sonar reading when lifted about 20cmScreenshot_2014-09-19-18-56-34.pngScreenshot_2014-09-19-18-57-40.png"
Sep 19, 2014
saqib shafiq replied to Randy's discussion ArduCopter-3.2 beta testing
"I did my range finder setup. I have an EZ4 sonar and did the settings according to the online instructions sonar settings for arducopter 3.2. When i lift copter above 20 cm then the readings seem fine. When it goes below that the reading shoot upto…"
Sep 19, 2014
saqib shafiq commented on Babis HatziIoannou's blog post ArduCopter RSSI voltage modification
"What version of apmplanner are you using? I dont even have the rssi_range option on mine. My rssi is on 160% because its set on the max 5v i think. Im using a 3.3v reciever. Is there any other way of changing the parameter?"
Sep 18, 2014
saqib shafiq commented on Euan Ramsay's blog post Mini hex + autotune = success.
"Its mounted on this jello platform using foam tape do you think it still might be affected by vibrations?"
Sep 11, 2014
saqib shafiq commented on Euan Ramsay's blog post Mini hex + autotune = success.
""
Sep 11, 2014
saqib shafiq commented on Euan Ramsay's blog post Mini hex + autotune = success.
"Im going to try take off in alt hold once i have fitted a sonar and get a chance to fly outside. Im thinking of using your pids to start off with for it to fly better than what it already does then fine tune it or auto tune once the alt hold works"
Sep 11, 2014
saqib shafiq commented on Euan Ramsay's blog post Mini hex + autotune = success.
"No when im hovering slightly a feet off the ground and i change to alt hold the motors go back down to starting speed? The controller flies well in stabilise. I thought its some setting with the throttle mid point? I havnt switched alt hold in mid…"
Sep 11, 2014
saqib shafiq commented on Euan Ramsay's blog post Mini hex + autotune = success.
"Looks very good thumbs up. Iv got a hex from HK. 330mm emax 1806 2300kv with 12a simon k esc. Iv got the apm full version which is a clone. It flies well in stabilise but not getting it to fly in alt hold. Do you think your pids will work with mine?…"
Sep 11, 2014