Comments

• Arwin March 8, 2014 at 8:16am

  ANyone Know how to make 2 APM2.6 working together 1 as master and another one for back up (Slave mode). I want to make redudancy 

  Reards

  LM Arwin 
• 

  Jay Johnson March 5, 2014 at 7:48am

  Anyone know where to buy compatible bullet/banana connectors for the 3DR copters?  I need to replace a motor and want to use the connectors that come with the blue motor.  This appears to be a 3.5 mm banana style plug, but not sure which exact female plug would be compatible - many of the images I see online appear to be squatter than what comes on the ESC.
• 

  Juan Federico Rossi March 3, 2014 at 1:41pm

  Any help to see what could happend? Here´s the last log. It falls in water, and i rescued 5 days after. Its and rc timer hexa combo, apm3.1, external compass (compasmot 4%), video tx400mw (lipo 1300ma) ,brushless gimbal and Gpor3(lipo1000mah).4500mah lipo for apm and motors. It used to fly really well, never something strange...but this time it ends in the bottom of the river...many thanks! 2014-02-16%2017-54.log

  https://storage.ning.com/topology/rest/1.0/file/get/3701675183?profile=original
• 

  Baja Brucie March 2, 2014 at 12:20pm

  Have hopefully backed 2 units.

  Plan to use horizontal and vertical  on my 3DR X8 2014 (on order)..

  Have heard (unofficially) from on high that Pixhawk is (or will be) compatible but

  cannot attest to that yet. Lidar could be a gamechanger.

  Syay tuned
• 

  Bob Kirkpatrick February 26, 2014 at 3:26am

  Can anyone tell me if the Pixhawk can use the new Lidar-Lite optical distance measuring device? It's I2c compatible, and so I assume it can plug into the I2C hub, but would the Pixhawk know what do do with it? Is is the same as sonar?

  Link to Lidar-Lite
• fercho hernandez February 18, 2014 at 2:28pm

  Hello friends I am new to this forum and do not know where to put my question pregutar or ....

  I have a poblem With Me hexacoptero Motado and have already configured with version 3.1 of apm arducopter ....

  Hoara to fly detachment and after a few minitus starts turning right and I can not straighten up and turn without losing control detenerce and estrellarce ....

  if I could help with this problem will thank a lot ...
• Developer

  Randy February 13, 2014 at 5:16pm

  Sufal,

      Re the PX4Flow.  It's not supported by the ArduCopter software yet.  This is mentioned on the bottom of the page in the 3dr store.  Unfortunately I think it's unlikely that it will ever be supported on the APM2 due to CPU limitations and lack of spare serial ports.  I'm pretty sure it will be supported on the Pixhawk in AC3.2 or AC3.3.  I've added a warning about lack of support for the APM2 to the wiki....  Sorry for the troubles.
• sufal thakuri February 13, 2014 at 10:49am

  Hi guys,

  Do anyone know how to connect PX4FOW with APM 2.6....?

  thanks
• minhaj February 13, 2014 at 7:54am

  hi guys  i also need some help ;

  i am giong to designe quadcopter with fpv camera which could be controlled from 5km range a collected all the data but i have still stuck with antenna.

  kindly guide me about long range antenna that could controll quad copter from 5km range

   
• Dennis Fuente January 19, 2014 at 12:01pm

  Hi Guys Need some help 

  So i finally have a new regulator installed and the board has come up on mission planner motors arm no more bad gyro health displayed in the data page but now i don't have any GPS it was working just fine what could be causing this to occur thanks for any help.

  Dennis