Discussion group for ArduCopter users

3180 Members
Join Us!

You need to be a member of diydrones to add comments!

Join diydrones

Comments are closed.

Comments

  • It is the airport overlay, if you hover your pointer over the red circles they will show you the airport name.  Baically to show you when you are close to an airport. You can turn it off in the configuration tab, as detailed in this post:

    http://diydrones.com/forum/topics/mission-planner-1-3-2

  • I haven't seen this on mine, maybe a view setting?

  • What is this on my map and how do I turn it off?!?!?

    It showed up when I downloaded the latest Mission Planner?3701881755?profile=original

  • Where do you find the settings in MP ft modes

  • ok so now I am stuck at getting the R7008sb to talk to PixHawk for my initial set-up.  Do I get a PPM encoder and use the 8 ports into PixHawk vai the encoder or is there another solution yet?

  • Can someone help on my posted question?

    http://diydrones.com/forum/topics/arduppm-v2-3-16

  • HI All
    I am new to RC and need some help. I have had problems setting up my TX (Senior Moment).
    Now using a EEPE file I got from friend that works. But some settings don't thats why i would
    like to find a file that someone is using on their Hex.  Maybe they will share the file with me.
    If it works for them it will for me as well with the equipment as i have.
    Any and all help would be greatly be appreciated.
    Johnny Moritz     Spring, Texas


    I have a:        Tarot 680 Hex Pro
                            Fysky Taranis x9d TX  and  a X8R Reciver
                            APM 2.6  with   uBlox GPS with Compass
                           MODE 2 USA


    Configed like this on the APM and Reciver
                           CH1  Thr
                           CH2  Ail
                           CH3  Ele
                           CH4  Rud
                           CH5
                           Ch6
                           CH7
                           Ch8

    I would like to have an EEPE file i can FLY (with Sounds)

    Modes             RTL
                              Alt Hold
                              Stabilize
                              Land
                              Loiter

    And Maybe        Auto
                               Acro
                              Circle
                              Sport

  • @Austin

    I recently had an issue where checking the reverse box [ in AMP Planner ] didn't reverse it as it should but if I did so in the full param list it did. 1 is normal  -1 is reverse.

     

  • Problems/issues drone quadricopter using 2.5 AMP last step "SETUP ALL IN ONE ESC"

    I just finished calibrating the setup and installation of a drone quadricopter with APM 2.5. with Mission planner last version.

    How do the tuning "all in one of the 4 esc" everything works perfect truttle and left control of movement.

    But as I go back mode 'normal I have serious problems on the speed' minimum or zero drone quadricopter better with truttle a low position to zero.

    anyone has any suggestion?

    Thank you for vs time and congratulations to the whole community '

    Bye Paul

    PS ** I hope I have posted in the forum corrected the problem thanks again to all a good weekend;)

  • Hi all

    tks for joing me in this group

This reply was deleted.

Drone flying to non visible point

Hi there,I encountered a problem, while flying in auto mode, with approching to point that was not set by trajectory and is not visible after downloading mission from flight controller by Mission Planner. Does anybody encountered similar problem. The situation is that in the middle flight I stopped the UAV and uploaded new mission and after changing to auto mode it starts to fly in some direction. It goes straight to some point, so I assume it's not mechanical problem. I attached the link to…

Read more…
0 Replies

TAKEOFF WITHOUT USING GPS

Hi,Im working on a autonomous drones and im using JETSON NANO and flight controller PIXHAWK .Im able to control my drone by giving rc commands on the MAVLINK terminal itself by connecting it with PIXHAWK but now i want a python code from which i can do some operations like:takeoff,left ,right,forward,backward…and i am not using GPS…Can anyone please help me…

Read more…
1 Reply · Reply by tellinglean Oct 17, 2022

HELP quadcopter: one motor twitching and stuttering

Hello guys,I have a problem with one motor, do not spin and making a sound (videos in attachment), I changed the motor to another ESC and is work, so I checked the connections on ESC and all connections looking great. any ideas or something I can do, iam trying to build YMFC32 Brokking .thank youhttps://youtu.be/LagBqwGbixkhttps://youtu.be/PU20nCxApcs

Read more…
0 Replies

Will AHRS_ORIENTATION=8 for Arducopter 3.2.1 on APM 2.5 using a traditional Heli

I have been Reading Chris Olsen posts and watching his videos on Arducopter with traditional Helis using a Pixhawk.I have inherited an older Trex 450 heli with the old Align 3G FBL hardware.  The FBL controller appears to be bad.  So I have an old APM 2.5 without a compass or GPS on board.  I just want to replace the failed Align 3G FBL system with the APM.Now I have to mount the APM under the skids on the heli so the APM will be upside down.I have Two questions.1)  Is the AHRS_ORIENTATION=8…

Read more…
0 Replies