Comments

• Moderator

  Nathaniel Caner November 25, 2014 at 5:51pm

  @Doug,

  I believe that is identifying the Washington, DC Metropolitan Area Special Flight Rules Area (or the "ADIZ" Air Defense Identification Zone).

  I don't think there is a way to disable it. You can turn off the airports, but I don't see a way to disable the display of these zones. It's interesting that it doesn't effect the Flight Planning page, just the Flight Data page. That really makes the Flight Data screen unusable for the Baltimore area in the zone.

  

  Regards,

  Nathaniel ~KD2DEY
• Paul G. November 25, 2014 at 5:27pm

  It is the airport overlay, if you hover your pointer over the red circles they will show you the airport name.  Baically to show you when you are close to an airport. You can turn it off in the configuration tab, as detailed in this post:

  http://diydrones.com/forum/topics/mission-planner-1-3-2
• 

  Michael Beaubien November 25, 2014 at 5:11pm

  I haven't seen this on mine, maybe a view setting?
• 

  Doug Walmsley November 25, 2014 at 4:32pm

  What is this on my map and how do I turn it off?!?!?

  It showed up when I downloaded the latest Mission Planner?
• johnny moritz October 30, 2014 at 9:48pm

  Where do you find the settings in MP ft modes
• 

  Mark Aylward October 27, 2014 at 1:34pm

  ok so now I am stuck at getting the R7008sb to talk to PixHawk for my initial set-up.  Do I get a PPM encoder and use the 8 ports into PixHawk vai the encoder or is there another solution yet?
• 

  Mark Aylward October 24, 2014 at 1:24pm

  Can someone help on my posted question?

  http://diydrones.com/forum/topics/arduppm-v2-3-16
• johnny moritz October 17, 2014 at 1:01pm

  HI All
  I am new to RC and need some help. I have had problems setting up my TX (Senior Moment).
  Now using a EEPE file I got from friend that works. But some settings don't thats why i would
  like to find a file that someone is using on their Hex.  Maybe they will share the file with me.
  If it works for them it will for me as well with the equipment as i have.
  Any and all help would be greatly be appreciated.
  Johnny Moritz     Spring, Texas

  
  I have a:        Tarot 680 Hex Pro
                          Fysky Taranis x9d TX  and  a X8R Reciver
                          APM 2.6  with   uBlox GPS with Compass
                         MODE 2 USA

  
  Configed like this on the APM and Reciver
                         CH1  Thr
                         CH2  Ail
                         CH3  Ele
                         CH4  Rud
                         CH5
                         Ch6
                         CH7
                         Ch8

  I would like to have an EEPE file i can FLY (with Sounds)

  Modes             RTL
                            Alt Hold
                            Stabilize
                            Land
                            Loiter

  And Maybe        Auto
                             Acro
                            Circle
                            Sport
• 

  Richard Kennedy October 5, 2014 at 8:10pm

  @Austin

  I recently had an issue where checking the reverse box [ in AMP Planner ] didn't reverse it as it should but if I did so in the full param list it did. 1 is normal  -1 is reverse.

   
• Paul October 3, 2014 at 9:53am

  Problems/issues drone quadricopter using 2.5 AMP last step "SETUP ALL IN ONE ESC"
  
  I just finished calibrating the setup and installation of a drone quadricopter with APM 2.5. with Mission planner last version.
  
  How do the tuning "all in one of the 4 esc" everything works perfect truttle and left control of movement.
  
  But as I go back mode 'normal I have serious problems on the speed' minimum or zero drone quadricopter better with truttle a low position to zero.
  
  anyone has any suggestion?
  
  Thank you for vs time and congratulations to the whole community '
  
  Bye Paul
  
  PS ** I hope I have posted in the forum corrected the problem thanks again to all a good weekend;)