Comments

• • 

    DexterIsMyHero > Keith Smith April 25, 2021 at 10:01am

    I worked through this on my hexacopter. ArduCopter's numbering of the motors is very specific, not a circle but three diagonals. 1 is the right side, 2 is the left, 3 and 4 are opposite, 5 and 6 are opposite. If you don't have them wired this way the Motor Test in Mission Planner would act that way. Also, it probably won't fly right. May just flip over and try to dig to china on you the first takeoff.
• 

  HawkEye UAS February 13, 2017 at 8:46am

  EMPLOYMENT OPPORTUNITIES......  Northeast Georgia

  HawkEye UAS is currently accepting applications for it's new UAV Pilot Apprentice Program.  The ideal candidates would live in the Gainesville, Georgia area.

  FAA Remote Pilot Certification would be a plus, but not required to begin the training process.

  Take a look at the job descriptions and see if this is something you would like to grow into.     http://www.hawkeyeuas.com/employment-opportunity.html

  Send all questions and replies directly to me at:    abe@hawkeyeuas.com

  

  Employment Opportunity
• paladin66 December 29, 2016 at 10:15am

  Hello,

  I have a Pixhawk PX4 Flight Controller and I want to use it with the PHANTOM 3 PRO  4K Camera https://hobbyking.com/en_us/phantom-3-accessory-spare-part-4k-camer.... Can you help me to connect this camera to my pixhawk and get it worked.

  Best regards

  

  Phantom 3 Accessory/Spare Part - 4K Camera

  Phantom 3 Accessory/Spare Part - 4K Camera
• 

  Larry A Amati November 20, 2016 at 2:14am

  hello fellow pilots.

  Has anyone heard of a aerial mapping system called VMAP?

  I have read that tower companies are starting to use drones to inspect and map their towers.

  Mapping
• Craig November 1, 2016 at 7:37am

  open MP then press control F and the select Param Gen on the left. 

  close it and MP. Open MP and connect to your APM and all the drop downs in flight mode should now be populated.
• 

  yuvraj November 1, 2016 at 6:57am

  hi can any one help me how to set of_loiter mode with apm 2.6 in mission planner i'm not able to see of_loiter mode in flight modes can any help me how to resolve this issue...
  
  Thanks.
• 

  Ray Quintana October 10, 2016 at 6:43am

  Asif what FC do you have?  I have an APM 2.8 on my rover and I had the compass jumper in the wrong spot, I had the same issue where I couldn't calibrate the compass.
• Asif Iqbal October 10, 2016 at 3:01am

  Hi all

  i have problem with my quadcopter.

  it flip as flying. i know i could not calibrate compass in mission planner. mission planner dont get sample when i move my ardupilot

  any one can help me?
• 

  Doug Adduci June 7, 2016 at 1:47pm

  I think there is a paperclip reset hole on the side of the pixhawk.  That should do it.
• david turner June 7, 2016 at 12:16pm

  Good evening 

  Is there a simple way to reset my pixhalk ? 

  I purchased one to put in my 650 tarot and used mission planner to set it up, as I am use to this.

  Then I read Qground control was better , don't believe everything you read.

  So tryed it and don't like it and thought I could just reinstalled program from mission planner.No you can't won't install firmware ,so I want to start all over again from fresh. Is there a way to do this ? Looked and asked intranet without any joy.

  Anybody?

  Regards Dave

  

  Planner