Pixhawk causing motor sync issues.

I believe I have a problem with my Pixhawk and was hoping for some help.  Also posted this on rcgroups.

The issue is that when my speed controllers are hooked up to the Pixhawk they exhibit a bad sync issue.  However when they are connected to my old APM (3.1) or just a receiver directly they do not exhibit these symptoms.  This has resulted in 4 crashes now until I just tonight narrowed down the issue to the Pixhawk.

Can anyone advise what is going on?  Here are the specs of my setup:

Afro 30A ESC's with SimonK firmware (have tried all versions, and made my own with various parameters)

Tiger MT2216-9 1100kv motors

4S 3700mah battery

https://www.youtube.com/watch?v=i7_gVoY8q8M

https://www.youtube.com/watch?v=VTK81IANyUE

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • Developer
    Pixhawk 2.1 has a solder option to provide 5V PWM

    The reality of this issue is that 95% of the time, it's due to bad wiring... but in the other 5% we have a solution for you.

    Hint... the green Solo cube comes with this mod :)
  • ...WTF? I still haven't heard back regarding my issue. I understand being busy as I am also a business, but if I can't get tech support then I have wasted my money...

    Whats so hard about a simple reply if you know the answer?

    Q: Why do I get a busy signal from all for of my Emax Simon Series 12A ESCs?

    APM 2.6

    Emax 12A SS

    Emax MT2204 ll

    Gemfan 6 in props

    Can anyone please advise? Or should I simply scrap the APM/Pixhawk product for Naza?

  • Hi,

    I just wanted to add my voice to the list of people who've experienced multiple crashes when running Pixhawk with Afro ESCs running Simonk (sorry, not sure which version specifically - whatever they were shipped with mid 2014).

    I've got multiple Pixhawk's and a bunch of Sunnysky 2212 980kv v2 motors driven with Afro Slim 20A. I've successfully used the same motor/esc combo on APM 2.6, Naze 32 running baseflight and cleanflight with success. But the Pixhawk + Afro ESC combo I've seen sudden de-sync and had the quadcopter fall out of the air on numerous occasions - three broken frames.... The latest on Sunday with a DJI 450 frame, after a manual tuning session I engaged auto tune to see what 3.3.1 would produce but during yaw tuning one motor de-sync'd and it fell 5 meters out of the air. I'd previously not figured out what was causing it, but after doing a bit of searching and finding that it's a common well documented issue over the last year, I'm just dumbfounded that the root cause isn't isolated yet, or maybe I didn't find the right post yet...  

    For now, I've flashed BLHeli and will do some bench testing...  fingers crossed.

    • same issue here with Hobbywing Quattro 4-in-1 ESC, just don't run AutoTune on that config and you'll stay in the air.

    • lol, just upgrade them already, running afro slims with 2216 800ies since January I've flashed them with blheli for easy of maintenance. 

      • Hi Artem, for easy maintenance we now have an APP pn Google for setting up properly and flashing SimonK. Here is the Link: https://chrome.google.com/webstore/detail/rapidflash/gehadojofkekob...

        I have not used it yet, but can't wait! I still had a flip again last WE changing from Baro back to Stabilize mode with Pixhawk after 10 minutes in the air! Harrrr. I rebuild it 2 times already changing all ESCs and Motors re-soldering the power distribution, twisting the signal cables etc... I will use your recommendations of using PWM_Com ON and high timing on the motors, as it seems this would help from your previous recommendations...

        Cheers, I trust most if you Guys will find this App useful for setting up your Simonk Firmware before flashing your ESCs. Enjoy and Safe Flying!

        RapidFlash
        Taking ESC flashing to the next level
  • motor sink issues can occur when you arm your copter the motors are set not to spin up . this can occurs from time to times just power cycle the copter should be fine. also seen this occur with pix hawk using the arming button enabled motors are set not to spin up one ESC can beep late. power cycle the copter. have better results removing arming button for some reason.

     

    • HI OG, you just replied to some of my concerns, but I could not reply directly to your post; when you are suggesting BLHeli, for PIxhawk.... Would you mind sharing compulsory settings on BLheli to get it to work properly, as with BLHeli testing many settings I gave up; as I crashed so many times with 920KV t-Motors and Afro Slim 20A ESC with BLHeli initially! Now I reverted back to SimonK and apart form one motor not spinning on arming; I recalibrate the ESCs and it flies, but not too confident.... I would rather get back to BLHeli; but I wish someone would share their settings for PIxhawk; as it is a serious headache guys!

      • Hello Guys,

        are you still using the arming button and having issues with bl-heli!!!!!

        suggest disable the arming button when Pix Hawk is your FC

      • hello,

        to be onset I have not needed to messed with the settings in BL Heli firmware I suspect this is where your going wrong. the simonK is not going to produce any better results. here is my original post on BL heli users have posted settings as well

        http://diydrones.com/profiles/blog/show?id=705844%3ABlogPost%3A1457...

        also if you looking for examples BL-Heli settings you can can find some here 

        http://www.olliw.eu/2012/owsilprog-tutorials/?en

        any issues from here on caused by the arming button disable it!

This reply was deleted.

Activity

DIY Robocars via Twitter
RT @TinkerGen_: "The Tinkergen MARK ($199) is my new favorite starter robocar. It’s got everything — computer vision, deep learning, sensor…
Monday
DIY Robocars via Twitter
Monday
DIY Robocars via Twitter
RT @roboton_io: Join our FREE Sumo Competition 🤖🏆 👉 https://roboton.io/ranking/vsc2020 #sumo #robot #edtech #competition #games4ed https://t.co/WOx…
Nov 16
DIY Drones via Twitter
First impressions of Tinkergen MARK robocar https://ift.tt/36IeZHc
Nov 16
DIY Robocars via Twitter
Our review of the @TinkerGen_ MARK robocar, which is the best on the market right now https://diyrobocars.com/2020/11/15/first-impressions-of-tinkergen-mark-robocar/ https://t.co/ENIlU5SfZ2
Nov 15
DIY Robocars via Twitter
RT @Ingmar_Stapel: I have now explained the OpenBot project in great detail on my blog with 12 articles step by step. I hope you enjoy read…
Nov 15
DIY Robocars via Twitter
RT @DAVGtech: This is a must attend. Click the link, follow link to read the story, sign up. #chaos2020 #digitalconnection #digitalworld ht…
Nov 15
DIY Robocars via Twitter
RT @a1k0n: Got a new chassis for outdoor races (hobbyking Quantum Vandal) but I totally didn't expect that it might cause problems for my g…
Nov 11
DIY Drones via Twitter
First impressions of the Intel OpenBot https://ift.tt/36qkVV4
Nov 10
DIY Robocars via Twitter
Nov 9
DIY Robocars via Twitter
Excellent use of cardboard instead of 3D printing! https://twitter.com/Ingmar_Stapel/status/1324960595318333441
Nov 7
DIY Robocars via Twitter
RT @chr1sa: We've got a record 50 teams competing in this month's @DIYRobocars @donkey_car virtual AI car race. Starting today at 10:00am…
Nov 7
DIY Robocars via Twitter
Nov 6
DIY Robocars via Twitter
RT @a1k0n: Car's view, using a fisheye camera. The ceiling light tracking algorithm gave me some ideas to improve ConeSLAM, and having grou…
Nov 5
DIY Robocars via Twitter
RT @a1k0n: To get ground truth I measured the rug, found the pixel coordinates of its corners, calibrated my phone camera with my standard…
Nov 5
DIY Robocars via Twitter
RT @a1k0n: @DIYRobocars is back in December, but outside. Time to reinvestigate ConeSLAM! I rigged up a quick and dirty ground-truth captur…
Nov 5
More…