About

Gender

Male


Location

Denver, CO


Please tell us a bit about your UAV interest

lots


Activity Feed

Bart Mowrey replied to Bart Mowrey's discussion Altitude loss with Yaw- advice needed
"No such luck. Ive actually been rebuilding mine from the ground up with different escs and see if that doesn't help resolve a few problems with sync holding in the stock units flashed w simonk. Ill update you if that has helped resolve most of my…"
May 1, 2013
Bart Mowrey replied to Nati's discussion APM 2.5, Motor setup: only one motor is working.
"Hi Nati- Ive seen that problem more than once, and never got a satisfactory answer here. From what i could tell it boiled down to a few things:
1. check all of your bullet's solder joints. You can test across the joint with a resistance test to help…"
Jan 5, 2013
Bart Mowrey posted a discussion
How would i get it back to default? is there some way to edit the code within the planner without having to fool with source?
Jan 4, 2013
Bart Mowrey posted a discussion
or, in what case does the ESC lose its calibrations or de- sync?The problem is this:  my Hex's ESCs have simonk firmware, and don't seem to hold calibration for very long. Granted I'm not an expert here and haven't yet flown a great many hours with…
Dec 9, 2012
Bart Mowrey posted a discussion
After reassembling my hex with a 2.5 apm and new hex pdb, I tried a test flight or two and after flipping a few times and busting a prop, i reduced my expectations to just a hand test or two so i could validate my wiring etc. However, as i would arm…
Nov 15, 2012
Bart Mowrey replied to Bart Mowrey's discussion Requesting RMA
"@DroneSavant- where'd your reply go? You'd said  "I dont think they do repairs anymore".
 
Is that the case? Did you delete the reply having learned differently? I think there's ample evidence of responsibility on my part to facilitate an exchange."
Sep 10, 2012
Bart Mowrey posted a discussion
prebuilt APM 2.0 with 2 dead or screwy output channels.No crashes.in short, when i converted my quad to a hex, 2 of the channels have started giving me fits.to wit, motor test in the CLI fails on 2 of the rotors. Ive swapped out the motors and ESCs…
Sep 10, 2012
Bart Mowrey replied to jordan lease's discussion "no heatbeat packets found"
"Have you updated to a new version of the mission planner? not too long ago, they updated to Mavlink 1.0 from .9 and if youre not using the updated MP software, it wont work."
Sep 10, 2012
Bart Mowrey replied to Alex Hills's discussion How do I tell if new motors are bad?
"simple test for motors- connect the affected motor's ESC lead to your throttle output on the receiver itself and spin it up from the radio without the APM in the loop. That will tell you if both the ESC and the Motor are working. If it doesnt run…"
Sep 10, 2012
Bart Mowrey replied to Bart Mowrey's discussion problematic hex conversion -
"Has anyone seen this behavior before? could it be due to brownout or is this an APM or ESC issue?"
Sep 7, 2012
Bart Mowrey posted a discussion
 former quad, converting to hex with a custom frame.Basically after building a custom frame and porting everything over, i now am having some odd problems that arent making sense to me. Im using APM 2.0, a stock pdb, motors, escs (flashed to…
Sep 6, 2012
Bart Mowrey replied to Bart Mowrey's discussion Quad to hex conversion = %50 more issues
"update- I mustve tested one of the good esc motor combos as Ive determined the issue to be 3 screwy ESCs. This brings up a number of other questions though, namely why? Especially when both were new from DIY store and the other worked wonderfully…"
Aug 27, 2012
Bart Mowrey posted a discussion
Im converting my quad to a hex for greater capabilities and have it all ready to fly, when surprise.... three motors wont spin up.Here's whats been done and tested: 1. All of the ESCs successfully flashed to the tgy.hex2. pdb checked for…
Aug 27, 2012
Bart Mowrey commented on Chris Anderson's blog post APM 2 cases now available, also come free with new APM 2s
"being that i have the soldering skills of a cappuchin monkey after an espresso, i elected to get a prebuilt one. No worries, though I can clip like a pro. Save for that, love the case!"
Jul 25, 2012
Bart Mowrey commented on Chris Anderson's blog post APM 2 cases now available, also come free with new APM 2s
"FWIW my case didnt fit either, even though it was stock, without the optional headers, but the board fastener pins were too tall under the lower profile area. I did have to clip all of them, even the ones by the gps module to make it fit. After…"
Jul 25, 2012
Bart Mowrey replied to Bart Mowrey's discussion Altitude loss with Yaw- advice needed
"I should also add, that this is a consistant thing, not just thick-thumbing the throttle( errr entirely)"
Jul 7, 2012
More…