About
Activity Feed
"Nice work.
Do you still have the initial version that was intended to run on the teensy ? I was thinking of utilizing it for as a starting point for a rover rc car controller?"
Do you still have the initial version that was intended to run on the teensy ? I was thinking of utilizing it for as a starting point for a rover rc car controller?"
"@Hai,
Did you ever get flymentor3d to work in high altitude ?"
Did you ever get flymentor3d to work in high altitude ?"
"@Owen, Well said , couldn't express it better.
Good luck for all."
Good luck for all."
"Great post. Keep up the good share."
"We are almost mid year, any news on the new Blimp"
"Thanks for your support.
I only have basic soldering skills, I tired my best to locate any another loose component but did not find any.
I checked VDD (pin 9,19 ) and they have good 3.1 volt , also the ground pins are connected.
I do not have an…"
I only have basic soldering skills, I tired my best to locate any another loose component but did not find any.
I checked VDD (pin 9,19 ) and they have good 3.1 volt , also the ground pins are connected.
I do not have an…"
Hi,I started off with an ArduCopter , it took me a while but after I linked the three PID to three RC channels I finally got it stable in the air.My PID where 3.20 , 0.32 , 1.11.I'm using 9ch Radio, CF2822 motors, 20A ESC towardpro, 1047…
"I had bad experience in this subject using similar combination, here is a reference to my previous thread:
http://diydrones.com/forum/topics/score-xbee-pro-2-receivers"
http://diydrones.com/forum/topics/score-xbee-pro-2-receivers"
"First of all thanks for all your support.
Mark, Chris:
I already purchased 900 series, this was based on your earlier warnings “thank you” never too late to correct , but I hoped that I still can use the 2.4 for something. I guess not.
Hessel,…"
Mark, Chris:
I already purchased 900 series, this was based on your earlier warnings “thank you” never too late to correct , but I hoped that I still can use the 2.4 for something. I guess not.
Hessel,…"
I created very simple setup to track the speed and altitude of my RC plane.On the plane: In addition to the AR500 spektrum 5 channels,XBee pro 2.4 connected directly to ublox 407 (RX,RT) they shared a regulated 5DC power source. power by a separate…
"This is the best I have found so far.
http://diydrones.com/profiles/blogs/arduimu-quadcopter-part-ii?xg_s..."
http://diydrones.com/profiles/blogs/arduimu-quadcopter-part-ii?xg_s..."
"I will give it one more day or so , in general it is getting me more experienced with the code and the tools.
Meanwhile I'll stay very excited until 2.5.1 is released.
Very good job and good luck.
Thanks"
Meanwhile I'll stay very excited until 2.5.1 is released.
Very good job and good luck.
Thanks"
"Sirs,
I tried ArduPilot 2.4 and every thing worked very well. (Station, xbee, ...)
when I switched back to ArduImuPilot every thing is still the same.
The following was the output of the arduimu to the pilot:
imu out…"
I tried ArduPilot 2.4 and every thing worked very well. (Station, xbee, ...)
when I switched back to ArduImuPilot every thing is still the same.
The following was the output of the arduimu to the pilot:
imu out…"
"I tried that, this is what happens:
I connect the FTDI first to the laptop
Connect the power to the pilot.
The station speed meter runs around and the current waypoint indicator sets to 999 , all of this happens during the initialization of the…"
I connect the FTDI first to the laptop
Connect the power to the pilot.
The station speed meter runs around and the current waypoint indicator sets to 999 , all of this happens during the initialization of the…"
"Hello everybody,
I'm new at this wonderful world,
I'm trying to run run Ardupilot + arduimu + xbee pro 2.4
So in addition to the above connections, I also have the xbee modules configured for 38400 and connected gnd, 5v , xbee rx pin to ardupilot…"
I'm new at this wonderful world,
I'm trying to run run Ardupilot + arduimu + xbee pro 2.4
So in addition to the above connections, I also have the xbee modules configured for 38400 and connected gnd, 5v , xbee rx pin to ardupilot…"
"Can we use 50 Channel GS407 or GS406 Helical GPS Receiver which is u-Blox 5H based (http://www.sparkfun.com/commerce/product_info.php?products_id=9436) with this board? What is the required configuration with it?
Thanks"
Thanks"
