About

Please tell us a bit about your UAV interest

FPV, RC, 3D Printing and more.....


Hometown:

Singapore


Activity Feed

IdefixRC replied to IdefixRC's discussion Pixhawk Relay - How to drive a 5V reed relay to trigger a camera
"Thanks a lot.
Final question :-) is there a way to control 2 relays via the remote?I believe Copter 3.2 only has the option to control the first relay via CH7 or 8, correct?"
Jul 1, 2015
IdefixRC replied to IdefixRC's discussion Pixhawk Relay - How to drive a 5V reed relay to trigger a camera
"Thanks for the reply.
Do you have a suggestion on the SSR type to use? Why would a resistor be required?
Thanks !"
Jun 29, 2015
IdefixRC replied to Gabriel DeVault's discussion Using pixhawk as a relay? in PIXHAWK
"Hi guyes,

I'm trying to short 2 pins inside a GoPro remote to trigger the camera shutter and have tried a circuit I found in another, older thread. Unfortunately it provides power to the reed relay when the relay is off (0v on the Pixhawk pin) and…"
Jun 28, 2015
IdefixRC replied to Phill Simpson's discussion Operating a relay with the Pixhawk Aux pin
"Hello Henri,

I'm trying to short 2 pins inside a GoPro remote to trigger the camera shutter and have tried your circuit. Unfortunately it provides power to the reed relay when the relay is off (0v on the Pixhawk pin) and opens the relay once the…"
Jun 28, 2015
IdefixRC posted a discussion
Hi,I'm using APM Copter 3.2 and I'm trying to add trigger as well as mode change capabilities to my GoPro camera. I'm currently exploring to hack the wifi remote that comes with the Hero3+ black so that I can control both the shutter as well as the…
Jun 27, 2015
IdefixRC replied to Chris Woods's discussion Pixhawk and Feiyu G3
"Sounds bad. I hope mine will last longer. 
My first Gimbal was a dys 3 axis with alex mos on a 3DR X8. Never managed to get it to work properly. 
The yaw axis sometimes worked, sometimes not (started to work once the circuit board was touched). It…"
May 15, 2015
IdefixRC replied to Chris Woods's discussion Pixhawk and Feiyu G3
"The point is that the Pixhawk needs to be up and running before power to the gimbal is applied as otherwise the firmware times out (now valid PWM signal) and locks the inputs. I wrote to Feiyu and the acknowledged that there is no workaround (or…"
May 15, 2015
IdefixRC replied to Chris Woods's discussion Pixhawk and Feiyu G3
"Hi,
I just installed the pixhawk in the XuGong and have exactly the same issue.
No tilt control (tilt channel connected to pixhawk) when I power the quad up. If I unplug the gimbal power and plug it back in after that I get all the control…"
May 7, 2015
IdefixRC commented on Heino R. Pull's blog post Using a Remzibi OSD with Arducopter 2.0.x Beta (and now Arducopter 2.7.3/2.8) and Mavlink 0.9/1.0
"Hello Heino,
I'm currently investigating how I can use the ImmersionRC XuGong V2 Pro OSD with a Pixhawk/APM.
The OSD that ships as part of the PDB is based on the EzOSD from Immersion and typically get's it's data from a Naze FC or  - based on the…"
Mar 8, 2015
IdefixRC replied to Alain's discussion Possibility of using EzUHF LRS for telemetry and RC control?
"I don't think that the EzUHF 2 way link is implemented yet.
I was looking for a similar solution and went the OpenLRS route with ULRS custom FW which allowed me to use a 1W Tx (possibly the real output power is more in the range of 400-500mW) module…"
Jan 3, 2015
IdefixRC replied to Rolf Blomgren's discussion APM MavLink to FrSky X8R S.Port converter
"Hi Luis,
Are you running the lua on the standard or the plus model of the Taranis? I'm using the plus model and see some of the telemetry data is cut off on the right hand side (e.g. gps fix). is there a place in the script which could be adjusted?…"
Oct 26, 2014
IdefixRC replied to Rolf Blomgren's discussion APM MavLink to FrSky X8R S.Port converter
"Hi Mike,
Simply change the code with a text editor and upload the file to your radio. There is no need to compile."
Oct 25, 2014
IdefixRC replied to Rolf Blomgren's discussion APM MavLink to FrSky X8R S.Port converter
"Now it makes a lot of sense. Well thought through and good to know. 
Yes, now i will definitely pay attention if he talks :-) "
Oct 23, 2014
IdefixRC replied to Rolf Blomgren's discussion APM MavLink to FrSky X8R S.Port converter
"Hi Luis,

first off all: AWESOME work.
I have the Teensy running now and your LUA script shows up nicely.
My flight modes are configured with SG for the 3 positions and SD to toggle between the 2 sets.
SD UP is set 1, !SD UP is set 2
The mix is…"
Oct 22, 2014