Gender
Male
About
Location
Patras
About Me:
Programing, UAV designing, electronic designing.
Please tell us a bit about your UAV interest
electronic, software, develope ;-)
Hometown:
Patras
Activity Feed
"SOOOOOO we are still hard working and soon YOU WILL FINALY know whats mean WOD !!!!!!!!!! :-)"
"so bill i made thread there
http://discuss.ardupilot.org/t/wod-gsc-guided-commands-ack-3/10146
pls help or i will go to crazzy from this ..... ;-)"
http://discuss.ardupilot.org/t/wod-gsc-guided-commands-ack-3/10146
pls help or i will go to crazzy from this ..... ;-)"
"i testing it now on CMD 221 , i think its simple message ( target sysid 1, target comp 1 )
in finalizing message im using sys id 255 ( gcs) and 0 for comp
STILL SAME RESULT ...... error 3 :(
do you want me make thread on…"
in finalizing message im using sys id 255 ( gcs) and 0 for comp
STILL SAME RESULT ...... error 3 :(
do you want me make thread on…"
"bill need guided commands some special sysID or comp ID ? or they supost to work in broadcasting (0,0) ?"
"bill i was check it before , andd python is realy not my strong skill :D i write my soft in C++.
But stil what i saw there ( first link ) im doing all right :( so was not help me
if you have idea what im DOING WRONG PRECISELY ;-) i will it realy…"
But stil what i saw there ( first link ) im doing all right :( so was not help me
if you have idea what im DOING WRONG PRECISELY ;-) i will it realy…"
can some one help me with those issue pls ?arducopter 3.3.3 / pixhawkafter msg11.target_system=1; msg11.custom_mode=4; …
"so first vido from short test ;-) just take off and land, but for first test of tablet version WOD-GSC .... so im happy that nothing fired,exploded, crashed etc....
https://www.facebook.com/petr.zverina.56/videos/1314048708623358/"
https://www.facebook.com/petr.zverina.56/videos/1314048708623358/"
"WOD GSC working, touch control full integrated, so soon first test in air ;-)"
"hi all , we transport now WOD-GSC to Acer iconia tablet ( win 8 and win 10 )
so soon some videos from test software ;-)"
so soon some videos from test software ;-)"
"so STP ( software trim proces ) work realy well, today tested , configuration :
GSC :
Laptop TAROX with 2nd gen i7
GSC-WOD v 0.55a
433mhz 500mw telemetry
Spektrum dx6i
Drone : HEXEN Mk1
Pixhawk clone
6x 2212/920 motors ,…"
GSC :
Laptop TAROX with 2nd gen i7
GSC-WOD v 0.55a
433mhz 500mw telemetry
Spektrum dx6i
Drone : HEXEN Mk1
Pixhawk clone
6x 2212/920 motors ,…"
"i found something strange. Is realy imposible make TRIM PROCES with 6 channel controler :-) i know is posible conect chanel 6 to chanel 7, but no if you use spectrum satelite straight to pixhawk. or soem receiver with PPM output, then you dont have…"
"so SETUP screen is near of finish ;-) now just left fence, PID ,tuning, and then only cosmetic stuffs ;-)"
"im sorry that i write again ;-) but i see that everyone put pictures and i dont made it :D my appologise for thread owner ;-)
So: we make now NEW GSC software WOD GSC. WOD is project what will present later , but even with out WOD this software…"
So: we make now NEW GSC software WOD GSC. WOD is project what will present later , but even with out WOD this software…"
"we working now on GRAPHICS for setup screen ;-) so this need some time ;-) soon will some results ;)"
"Accelerators calibration WORKing ( left down in text box is result ;-) so we will ready for first test fly under WOD-GSC soon ;-)
i know that i can fly now ;-) but i want make it realy just by WOD, includet all callibration processes ;-)"
i know that i can fly now ;-) but i want make it realy just by WOD, includet all callibration processes ;-)"
"Problem solved thanks to Randy ;-) for case that someone have same problem ,
Firmware wait for meesage 77 ( command_ACK ) ;-) paramteres 241,0 works well , but probably parameters are ignored ( so you can put there what ever you want ) ;-)"
Firmware wait for meesage 77 ( command_ACK ) ;-) paramteres 241,0 works well , but probably parameters are ignored ( so you can put there what ever you want ) ;-)"
