About

Gender

Male


Location

Tapa


Please tell us a bit about your UAV interest

F3C with Trex 500 and 600 Pro; UGV with APM 2,5+ and Pixhawk


Hometown:

Tapa


Activity Feed

Raimo Noormaa replied to Raimo Noormaa's discussion uBlox LEA 6H on APM and Pixhawk in ArduRover User Group
"I got the 2 GPS working. The only way I was able to use LEA6H as second GPS was to connect a USB charger (unpowered) to the GPS USB port for a moment and remove it. It seems that it needs tohave a power consumption peak."
Nov 20, 2014
Raimo Noormaa replied to Brian Sigmon's discussion Differences between old 3DR radio and V2 radio?
"Hi,

It works. I use the V1 with the USB on my ground station and the V2 on my Rover and Plane

Regards,
Raimo"
Oct 25, 2014
Raimo Noormaa left a comment on ArduRover User Group
"Is the sonar aka range-finder function working now?"
Oct 11, 2014
Raimo Noormaa replied to Thomas J Coyle III's discussion How to Install Dual Sonars on a Pixhawk in ArduRover User Group
"Have you been in contact with Tridge, is there any hope it will be resolved in near future, year 2014?"
Oct 2, 2014
Raimo Noormaa replied to Thomas J Coyle III's discussion How to Install Dual Sonars on a Pixhawk in ArduRover User Group
"Hi,

HC-SR04 signal is not fed directly to Pixhawk/APM - the signal activation, calculations, processing and conversion is done with Arduino Micro. The output is just voltage from 0 to 3V - analog. I modified the code so that it will not go above…"
Sep 21, 2014
Raimo Noormaa replied to Raimo Noormaa's discussion Motor activation in auto mode in ArduRover User Group
"Hi,

I actually don't know what was the reason I got it working. I did update (to the current version) firmware and after that it worked. You can try to reload the firmware, it should not hurt.

What you can check additionally is how you have…"
Sep 21, 2014
Raimo Noormaa replied to Thomas J Coyle III's discussion How to Install Dual Sonars on a Pixhawk in ArduRover User Group
"@Thomas

Full Parameter list, search for Sonar:
https://lh5.googleusercontent.com/-RC8l8JvC9pg/VB737YPyE3I/AAAAAAAA...
Full Parameter list, search for Sonar, result:
https://lh4.googleusercontent.com/-4C3sp0HYZXU/VB736yaQ4zI/AAAAAAAA...

Search…"
Sep 21, 2014
Raimo Noormaa replied to Thomas J Coyle III's discussion How to Install Dual Sonars on a Pixhawk in ArduRover User Group
"@Thomas

I dont understand the reason for this question: "Why are you using  RNGFND_PIN = 13 and 14, RNGFND_TYPE = 1 (analog) on the Pixhawk?"

Are the instructions about pin mapping and MP comments wrong?

Regards,
Raimo"
Sep 21, 2014
Raimo Noormaa replied to Thomas J Coyle III's discussion How to Install Dual Sonars on a Pixhawk in ArduRover User Group
"Hi,

Because you have stated that the 3,3V ADC input 1 and input 2 needs to be mapped to pin 14 and 13 aka Sonar Pin 14 (Left sonar), Sonar Pin 13 (Right sonar). According to MP RNGFND_TYPE comment I need to use analog = 1.

HC_SR04 signal is…"
Sep 21, 2014
Raimo Noormaa replied to Thomas J Coyle III's discussion How to Install Dual Sonars on a Pixhawk in ArduRover User Group
"Hi,

I need help with enabling The SONAR.

Description of problem and setup:
MP 1.3.9
Rover 2.46

Pixhawk: RNGFND_PIN = 13 and 14, RNGFND_TYPE = 1 (analog)
APM 2.5: RNGFND_PIN = 0 and 1, RNGFND_TYPE = 1 (analog)

Under CLI I have tested SONARTEST…"
Sep 21, 2014
Raimo Noormaa posted a discussion in ArduRover User Group
Hi,I started to play around with computer vision - recognizing some patterns is great. Currently do it on my laptop (MS VB + integrated webcam)I would like to hear your comments about using different hardware for CV.I plan to use a good quality USB…
Sep 15, 2014
Raimo Noormaa replied to Apostolos's discussion control signals required for mode and waypoint manipulation ???? in ArduRover User Group
"Hi,
 
It's not that simple. You must assign that specific pwm signal to a correct channel, witch you will need to calibrate later. How to assign
 
the signal to correct channel using your hardware i do not know.
 
Regards,
Raimo"
Sep 4, 2014
Raimo Noormaa replied to Apostolos's discussion control signals required for mode and waypoint manipulation ???? in ArduRover User Group
"Hi,

You can try to use suggested default values but it is not advised because you can damage your servos if you make it travel too much. After servo binding you can overload power circuits on the servos and on the APM.

So you can use these values…"
Sep 4, 2014
Raimo Noormaa replied to Raimo Noormaa's discussion uBlox LEA 6H on APM and Pixhawk in ArduRover User Group
"Hi,

Now it works and with the old power unit it did not work before. It really makes me feel uneasy when I don't know what was the actual reason what got it working.

Is it possible that the unit would not work correctly because of the battery that…"
Sep 4, 2014
Raimo Noormaa replied to Raimo Noormaa's discussion uBlox LEA 6H on APM and Pixhawk in ArduRover User Group
"Hi,

I powered all the units through GPS USB port and all works, even GPS :) . It seems that I just need more power for all the stuff connected to the board...

Frustrating to find out such simple problems with so much effort.

It's similar to a…"
Sep 4, 2014
Raimo Noormaa replied to Raimo Noormaa's discussion uBlox LEA 6H on APM and Pixhawk in ArduRover User Group
"Hi,

I replaced on the custom cable tx and rx, it was not correct before, Thank You!

Still I have the power issue witch makes no sense at all. When I connect the GPS to APM or Pixhawk the power led lights up but MP shows No GPS, when I connect…"
Sep 3, 2014
More…